Related Products: Heavy Duty Auto Drain Series ADH4000 Use piping of 1/2B bore size or larger for drain inlet and allow for unobstructed flow-in for drain. 2. Drain line should be 8 mm or more in diameter and less than 10 m in length. Do not make any upward angles in drain line.
Bore size (mm) Operating direction Operating pressure (MPa) Note 3) Note 1) Bore size (mm) Foot Flange Double clevis 0.3 181 241 317 377 495 589 841 935 0.5 302 402 528 628 825 982 1400 1560 0.7 422 563 739 880 1150 1370 1960 2180 IN OUT IN OUT IN OUT IN OUT 32 40 50 63 CLQ-D032 CLQ-D040 CLQ-D050 CLQ-D063 CLQ-F032 CLQ-F040 CLQ-F050 CLQ-F063 CLQ-L032 CLQ-L040 CLQ-L050 CLQ-L063 32 40 Note 1
The mounting direction is shown in the diagram below.
P. 13 Straight union Plug-in elbow Different diameter tee Use to change by 90 in a tube fetching direction from Onetouch fittings. P. 11 KGH KGL KGT P. 15 Use to connect tubes with size down in both 90 directions. Use to connect tubes in the same direction.
MGQ Theoretical Force MGG (N) MGC IN OUT Cylinder bore size (mm) Operating pressure (MPa) Operating direction Piston area (mm2) 0.7 0.5 0.3 MGF 84.8 IN 59 42 25 12 113 OUT 79 57 34 CY1 151 IN 106 75 45 16 201 OUT 141 101 60 MY1 236 IN 165 118 71 20 314 OUT 220 157 94 378 IN 264 189 113 25 491 OUT 344 245 147 603 IN 422 302 181 32 804 OUT 563 402 241 1056 IN 739 528 317 40 1257 OUT 880 628
Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping, vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or other applications unsuitable for the standard specifications described in the
Do not operate with the stroke adjusting unit fixed in an intermediate position. When the stroke adjusting unit is fixed in an intermediate position, slippage can occur depending on the amount of energy released at the time of an impact. In such cases, the use of the adjusting bolt mounting brackets, available per made-to-order specifications -X416 and -X417, is recommended.
Products represented in this catalog are designed for use in compressed air appllications only (including vacuum), unless otherwise indicated. Do not use the product outside their design parameters. Please contact SMC when using the products in applications other than compressed air (including vacuum). Operating Environment Warning 1.
It may result in degrading its accuracy. 5. Supply pressure Set supply pressure 0.3 to 0.5 MPa to brake release port. When supply pressure is below 0.3 MPa brake may not be released, when it is over 0.5 MPa brake life may be shortened. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.
In the case of w/o air cushion, it comes with rubber bumper.
In the case of w/o air cushion, it comes with rubber bumper.
A certain amount of leakage is allowed in the product's specifications. Warning 1. Confirm that PTFE can be used in application. PTFE powder (Polytetrafluoroethylene resin) is included in the seal material. Confirm if the use of it may cause any adverse effect in the system. Mounting Mounting Warning Warning 1.
880 IN 1103 221 331 441 551 662 772 45 14 OUT 1590 318 477 636 795 954 1113 IN 1436 287 431 575 718 862 1006 50 18 OUT 1963 393 589 785 982 1178 1374 IN 1709 342 513 684 855 1025 1196 56 18 OUT 2463 493 739 985 1232 1478 1724 IN 2209 442 663 883 1104 1325 1546 63 18 OUT 3117 623 935 1247 1559 1870 2182 IN 2863 573 859 1145 1431 1718 2004 67 18 OUT 3526 705 1058 1410 1763 2115 2468 IN 3271
In this case, the rigidity of the machinery should also be examined. 5. Consider a possible drop in operating pressure due to a power outage, etc. When a cylinder is used in a clamping mechanism, there is a danger of work pieces dropping if there is a decrease in clamping force due to a drop in circuit pressure caused by a power outage, etc.
Do not operate with the stroke adjustment unit fixed in an intermediate position. When the stroke adjustment unit is fixed in an intermediate position, slippage can occur depending on the amount of energy released at the time of an impact. In that case, use a short spacer or a long spacer. For other lengths, please consult with SMC.
One-touch installation and removal Employs the unique built-in keying mechanism which provides one-touch installation and removal capability even in hard to see locations. In addition, it prevents installation mistakes when reconnecting.