An approximate plate-end deflection X without a load is shown in the table below.
Load to piston rod must always be in an axial direction. Retaining Ring Installation/Removal Caution 1. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring). 2.
KQ2U KQ2VF KQ2W P. 53 P. 46 P. 49 Use to branch line in the same direction from female thread. KK D MS Female elbow Male delta union Plug-in reducer KQ2D P. 56 KQ2LF KQ2R P. 53 P. 46 Use to pipe at right angles to male thread. LQ Use to branch line in 90 direction from female thread. Use to change size of One-touch fittings.
Do not use these values for the thermal set values, etc. *7 Product other than the Option R is not equipped with an earth leakage breaker. Purchase an appropriate earth leakage breaker separately.
When equipped with an indicator light, be careful not to damage the light with the cord's lead wires.
It turns OFF when an alarm occurs or when JOG movement takes place.
Caution Single solenoid SJ3000-46-SC-l Double solenoid, 3 position type, 4 position type SJ3000-46-DC-l Connector Assembly Part No.
When in the locked state, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc. Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of over-run when an intermediate stop is performed.
When in the locked state, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc. Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of over-run when an intermediate stop is performed.
If it is equipped with an auto drain, check its operation once a day. yWhen the hydraulic pressure of an air-hydro unit must be raised. uWhen the pressure must be raised in an explosion-proof environment. iTo boost the pressure by remote operation, using an air operated type. rExhaust air After operating this product for an extended time in the set state, if the booster valve is switched,
Panel mount adapter ZS-46-B Panel mount adapter + Front protective cover ZS-46-D Lead wire with connector ZS-46-5F 5 cores, 2 m, waterproof Front protective cover ZS-27-01 R1/8 piping adapter ZS-46-N1 NPT1/8 piping adapter ZS-46-N2 -9No.PS-OMV0006-D Summary of Product parts Names of individual parts Operation light: Displays the switch operating condition.
Refer to p.0-39 through 0-46 for Safety Instructions and common precautions.
When the conduit type is used as equivalent to an IP65 enclosure, install a wiring conduit etc. 7. When an impact, such as water hammer etc., caused by the rapid pressure fluctuation is applied, the solenoid valve may be damaged. Give an attention to it. 3. Air quality
If operated with the workpiece gripping point beyond the indicated ranges, an excessive offset load will be applied to the sliding section of the fingers, which can have an adverse effect on the service life of the product.
Double solenoid V110N-D5MOZConnector assembly (for junction common) SJ3000-46-SC Single solenoid V110N-S5MOZConnector assembly (for junction common) SJ3000-46-DC Common wiring Connector assembly SJ3000-46-S (Example) VV100-10-04U1-C6 1 set V110N-S5MOZ-C4 2 sets V110N-D5MOZ-C4 2 sets SJ3000-46-S 1 set (Connector assembly for single solenoid) SJ3000-46-SC 1 set (Connector assembly for single
Never use them in the presence of an explosive gas, as this may cause a serious explosion 2. Do not use in an area where a magnetic field is generated. Auto switches will malfunction or magnets inside cylinders will become demagnetized if used in such an environment. 3. Do not use in an environment where the auto switch will be continually exposed to water. 1.
Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 20Data Stop signal Amount of overrun 6-12-29 Series C95N Specific Product Precautions 2 Be sure to read before handing. Adjustment Pneumatic Circuit Mounting Warning Warning Warning 2. Do not apply an offset load to the piston rod.
Take appropriate measures to avoid freezing of drain, moisture etc. by use of an air dryer. Not suitable for use as an emergency shutoff valve The valve represented in this catalog is not intended for use as an emergency shutoff valve.
ZS-46-B Panel mount adapter ZS-46-D Panel mount adapter + Front protection cover ZS-46-5L Power supply/output connection lead wire 5-core, 2 m ZS-27-01 Front protection cover B Panel mount adapter Connection Example ZS-46-B PFG300 Sensor connector D Panel mount adapter + Front protection cover PF3A7 H Power supply/output connection lead wire ZS-46-D Lead wire and M12 connector (Option for
Note) The high pressure switch can also be in operation for IDFB55E-46 and IDFB75E-46.