CY1F Therefore, it is important to secure as a danger zone a cylindrical area with the length of the clamp arm as its radius, and the stroke plus 20 mm as its height. 123 135 155 203 363 518 65 56 Head flange (including mounting bolt) 130 150 175 209 371 578 69 58 Calculation: (Example) MKG20-10RNZ Standard calculation: MKB20-10RZ Extra weight calculation: Head flange With arm ...222 g .130
D-M9 D-M9V D-F9W D-F9WV D-A9 D-A9V D-F9BAL Bore size (mm) A B A B A B A B A B A B A B 12 40.5 4 41 4.5 38 2 46 9.5 39.5 3 43.5 7 42.5 6 20 47 13 47.5 13.5 44.5 10.5 52.5 18.5 46 12 50 16 49 15 32 55 17 5.5 17.5 52.5 14.5 60.5 22.5 54 16 58 20 57 19 40 79 39 79.5 39.5 76.5 36.5 84.5 44.5 78 38 82 42 81 41 50 82 44 82.5 44.5 79.5 41.5 87.5 49.5 81 43 85 47 84 46 63 85.5 41.5 86 42 83 39 91
Note) When an AS-i compatible S kit is used, there is a limit on the maximum number of stations. For details, please refer to page 14. DeviceNet DeviceNet CC-Link CC-Link PROFIBUS-DP PROFIBUS-DP Remote I/O AS-i CANopen Nil +COM. COM.
of outputting the piston stroke movement as a pulse signal.
0.12 0.11 0.48 0.19 0.12 The VK3000 series can be used as 3 port valve, as a N.C. or N.O. type, by plugging either A or B cylinder Port.
low wattage 2 W DC) M5 x 0.8 0 to 0.7 Series VK3000 can be used as 3 port valve, as a N.C. or N.O. type, by plugging either A or B cylinder Port.
As a result, it is necessary for the customer to verify conformity to the EMC directive for the machinery and equipment as a whole. w For the servo motor (24 VDC) specification, EMC compliance was tested by installing a noise filter set (LEC-NFA). Refer to page 568 for the noise filter set.
In order to further improve stopping accuracy, the time from the stop signal to the operation of the lock should be shortened as much as possible. To accomplish this, use a device such as a highly responsive electric control circuit or solenoid valve driven by direct current, and place the solenoid valve as close as possible to the cylinder. 1.
When stopping a load in mid-stroke using an external stopper, etc., operate within the operating pressure limits shown in the table below. Use caution, as operation at a pressure exceeding these limits can result in breaking of the magnetic coupling.
As viewed from the end of the rod, the pin is tilted 15 to the left of the center. 3. Supply an air pressure of 0.3 MPa or more to the unlocking port. 4. Rotate the pin 30 to the right with a wooden implement such as the grip of a wooden hammer or a resin stick without scratching.
Note) When tightening an auto switch mounting screw, use a watchmakers screwdriver with a handle of approximately 5 to 6 mm in diameter. Also, tighten with a torque of about 0.05 to 0.1 Nm. As a guide, turn about 90 past the point at which tightening can first be felt. D-X 719
back flow mechanism as a standard feature.
When stopping a load in mid-stroke using an external stopper, etc., operate within the operating pressure limits shown in the table below. Use caution, as operation at a pressure exceeding these limits can result in breaking of the magnetic coupling.
B D A A B D B D Dimensions (mm) Dimensions (mm) Dimensions (mm) A B C D E F Y A B C D E F G Y A B C D E F Y Model Model Model ZP40HB ZP63HB ZP100HB 40 41 28 43 20.5 30 13 63 65 46 68 31.5 50 4.5 21.5 100 103 69 107 47.5 80 35.5 ZP125HB ZP50HB ZP80HB 50 52 36 54 24 40.5 16.5 80 83 58 85 37 64 5 27.5 125 129 89 135 56 105 44 1213 Series ZPT/ZPX How to Distinguish Different Pad Materials How
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Fluid quality The use of fluid which contains foreign matter can cause problems such as malfunction and seal failure by promoting wear of the valve seat and core, and by sticking to the sliding parts of the armature, etc. Install a suitable filter (strainer) immediately upstream from the valve. As a general rule, use 80 to 100 mesh. Caution 1.
When adjusting the stroke, use the distance from the end of the adjustment bolt to the end of the adjuster holder as a guideline. If dimension A is made smaller than 0, the slide table and adjuster holder will collide, resulting in damage to the slide table such as scratches or gouges.
-2 wBQ2-012 Two types of auto switch mounting bracket are used as a set.
Micro-Mist Separator Regulator AWD20/30/40 Series AWD is a component made up of a regulator and a micro-mist separator that are integrated to provide optimum results in applications such as ultraclean air blow operations.