7ND9071en Select between two values 2-A or 1-A using the + and keys. The value 2-A indicates a double acting actuator and 1-A a single acting actuator. To conclude press the ?
Do not apply a large impact or excessive moment to the slide table (slider). Because the slide table (slider) is supported by a precision bearing, do not apply a large impact or excessive moment when mounting a workpiece. 2. Align carefully when connecting to a load with an external guide mechanism.
A B Hs A B Hs Hv Hv Hv Hv 12/16/20 12/16/20 Hs Hs 25/32/40 25/32/40 Proper Auto Switch Mounting Position Solid state switch Bore size (mm) 2-color indication solid state switch Reed switch D-A9 D-A9V D-M9 D-M9V D-F9W D-F9WV A B C A B Hs Hv A B A B Hs Hv A B C A B Hs Hv C 15.5 15 20 20 15 19.5 19.5 19.5 19.5 46 46 46 46 18 13 15.5 35.5 42 31.5 42 31.5 12 17 17 22 22 17 21 21 21 21 47.5 47.5
Supply an air pressure of 0.3 MPa or more to the unlocking port. 4. Rotate the pin 30 to the right with a wooden implement such as the grip of a wooden hammer or a resin stick without scratching.
In an environment where vibration or impact occurs, provide an intermediate support even if the distance is within the allowable range in the graph. 1. Do not apply a large impact or excessive moment to the slide table (slider). Because the slide table (slider) is supported by a precision bearing, do not apply a large impact or excessive moment when mounting a workpiece. 2.
In an environment where vibration or impact occurs, provide an intermediate support even if the distance is within the allowable range in the graph. 1. Do not apply a large impact or excessive moment to the slide table (slider). Because the slide table (slider) is supported by a precision bearing, do not apply a large impact or excessive moment when mounting a workpiece. 2.
Use of a single solenoid will result in an unused control signal. If this is not desired, order with a specified layout. Note 2) Specified layout: Indicate wiring specifications on a manifold specification sheet. (Note that double, 3 position and 4 position valves cannot be used where single solenoid wiring has been specified.)
Plate Cylinder Series MU Double Acting: Single Rod Type/Double Rod Single Acting: Spring Return/Spring Extend 25, 32, 40, 50, 63 By adopting an elliptical piston design, a slim, square shaped body has been achieved, resulting in a space saving cylinder with unrestricted mounting directions.
For the protective tube, use a tube I.D. 7 or more, which excels in heat resistance and flexibility. Please contact SMC if an inverter welder or a DC welder will be used.
Compact lock unit is light weight and saves space Overall length has been reduced by using an independent brake cylinder (15% compared to P/A products).
Note 3) A reference value for correcting an error in reciprocal operation. Note 4) Impact resistance: No malfunction occurred when the actuator was tested with a drop tester in both an axial direction and a perpendicular direction to the lead screw. (Test was performed with the actuator in the initial state.)
Tighten them once again in such a case. 1. Be certain to use an pneumatic circuit which will apply balancing pressure to both sides of the piston when in a locked stop.
CRB2 Counter-clockwise A port Positioning pin hole 5 Adjustment bolt A CRB1 (For counter-clockwise rotation end adjustment) 22 95 .5 e MSU ng Adjustment bolt B ra t (For clockwise rotation end adjustment) en CRJ tm se wi us ck dj a lo CRA1 -c nd B port er se Clockwise e nt wi on Cl ck u lo o oc C ad ti CRQ2 C ta 90 k ju ro wi st 1 se m r ge en ot With Adjustment Bolt at t r an io n an
In cases where a positioning repeatability of 0.1 mm or less is required at the retraction and extension ends, use an external stopper for stops. Use of an internal stopper will result in approximately 0.1 mm of displacement due to changes in the operating pressure and external forces. 4. Use an external guide to receive a moment or torque which can generate a load.
In cases where a positioning repeatability of 0.1 mm or less is required at the retraction and extension ends, use an external stopper for stops. Use of an internal stopper will result in approximately 0.1 mm of displacement due to changes in the operating pressure and external forces. 4. Use an external guide to receive a moment or torque which can generate a load.
Note) When tightening an auto switch mounting screw, use a watchmakers screwdriver with a handle of approximately 5 to 6 mm in diameter. Also, tighten with a torque of about 0.05 to 0.1 Nm. As a guide, turn about 90 past the point at which tightening can first be felt. D-X 719
D-M9 D-M9V D-F9W D-F9WV D-A9 D-A9V D-F9BAL Bore size (mm) A B A B A B A B A B A B A B 12 40.5 4 41 4.5 38 2 46 9.5 39.5 3 43.5 7 42.5 6 20 47 13 47.5 13.5 44.5 10.5 52.5 18.5 46 12 50 16 49 15 32 55 17 5.5 17.5 52.5 14.5 60.5 22.5 54 16 58 20 57 19 40 79 39 79.5 39.5 76.5 36.5 84.5 44.5 78 38 82 42 81 41 50 82 44 82.5 44.5 79.5 41.5 87.5 49.5 81 43 85 47 84 46 63 85.5 41.5 86 42 83 39 91
Bore size (mm) A B A B A B A B A B A B A B 12 40.5 4 41 4.5 38 2 46 9.5 39.5 3 43.5 7 42.5 6 20 47 13 47.5 13.5 44.5 10.5 52.5 18.5 46 12 50 16 49 15 32 55 17 5.5 17.5 52.5 14.5 60.5 22.5 54 16 58 20 57 19 40 79 39 79.5 39.5 76.5 36.5 84.5 44.5 78 38 82 42 81 41 50 82 44 82.5 44.5 79.5 41.5 87.5 49.5 81 43 85 47 84 46 63 85.5 41.5 86 42 83 39 91 47 84.5 40.5 88.5 44.5 87.5 43.5 Operating
A B C A B A B A B A B Application Same tubing size 1 2 1 2 1 2 3 1 2 1 2 1 2 Refer to the applicable tubing table.
BQ2-012 is a set of d and e shown above. 32 to 100 When tightening an auto switch mounting screw, use a watchmakers screwdriver with a grip diameter of 5 to 6 mm.