Direct Operated Precision Regulator Modular Style Series ARP3000 1 Do not use a lubricator on the inlet side because it could clog the bleed holes and lead to a malfunction. 14-4-60 1 Regulator for 2 MPa Series ARX20 F.R.L.
Do NOT pipe upwards. AU200/300 Effective thread depth 6.5 4-M5 x 0.8 AU200, 300 Float type auto-drain Port size H G F E D C B A Model Port size 1 4 / 3 8 AU200 / 50 70 61 30 40.5 31.5 164 165 AU300 50 70 61 30 40.5 31.5 188.5 165 14-3-12
The silencer's response properties do not change in the initial stage, but will change due to the blockage after long use. Replace it after using about 500,000 times. This number is subject to change based on fluid quality and energization time. 2. When using a silencer, make space for silencer replacement. 1.The controller starts its output the moment the power switch is turned ON.
SlA w Note that in case of the option of different "1(P)" porting position, porting indication on the body and flow direction by handle operation are reversed. e Do not supply air pressure from other ports than 1(P) port. The valve may have air leakage when air pressure is supplied from other ports.
Note) Do not use excessive force to remove the connector as this might loosen the wire connections inside the connector. Open the cover by inserting a small flat head screw driver into the slot on the side of the pilot assembly(see drawing below), lift the cover out about 1 mm and then pull off.
Do not use it in a line that is kept pressurized because it could cause the body to break. 13-10-2 3 Air Suction Filter Series ZFA 100 200 Dimensions: ZFA Single unit Bracket ZX ZR Cover opened-up dimensions 70 Element extracted dimensions 55 ZM ZH ZU Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800)
Do not use a pair of pliers, nippers, or scissors because they could result in an uneven cut or cause the tube to become flattened. As a result, it might not be possible to connect the tubing, or after the tube has been connected, it could pull out or allow air to leak.
Reconfiguring the operation mode, as well as the zero and span adjustments, are easy to do in the field. INSTALLATION A B c D Installation Transmission oin & Feed-back lever Fig. 1 SINGLE.ACTING ACTUATOR OPERATION ACTUATOR SIGNAL RANGE INSTALLATION STYLE (REFFIG. 1) OUT 1 OUT2 Direct ?
Reconfiguring the operation mode, as well as the zero and span adjustments, are easy to do in the field. INSTALLATION A B c D Installation Transmission oin & Feed-back lever Fig. 1 SINGLE.ACTING ACTUATOR OPERATION ACTUATOR SIGNAL RANGE INSTALLATION STYLE (REFFIG. 1) OUT 1 OUT2 Direct ?
(Do not cut the tube with plier6, nippers, scissors, utilitv knife, etc.) ePull out the tube while keeping the release button depressed. lJf the release butlon is nol held down, the tube cannot be withdrawn.) OGrasp the tube, then slowly push it until il comes lo a dead-end.
Lubrication aTh yah,e h8 bon lub,ric.td ior ltb d nrlnubcfrirE. and dor noa lqoirr fudfiar fubdcdion in svba. ef a lubricant is used in the system, use turbine oil type #1 (lSO VG32). lf lubricant has been used in the system, do not cease to lubricate, as the original lubricant applied during manuiacturing will have been washed away. See table of suggested lubricants.
So, do not use under such conditions. Caution 1. Tightening the fittings and their torque When screwing fittings into the valve, make sure to tighten them to the proper torque values given below. Connection thread: M5 First, tighten by hand, then use a wrench appropriate for the hexagon flats of the body to tighten an additional 1/6 to 1/4 turn.
Do not plug or tighten it. Rc 1 1 2, 3 4, Rc 1 1 2, 3 4, (P port) (A port) Rc 1 1 2, 3 4, (R port) 1808 Series VGA342 Made to Order Specifications Please contact SMC for detailed specifications, dimensions and delivery.
4 3 Port Solenoid Valve Direct Operated Poppet Type Series VKF300 How to Order Valves Electrical entry G: Grommet (Lead wire length: 300 mm) Rated voltage D: DIN terminal DO: DIN terminal H: Grommet (Lead wire length: 600 mm) 50 60 1 2 3 100 VAC, Hz 200 VAC, Hz 110 VAC, Hz 220 VAC, Hz 24 VDC 12 VDC 240 VAC, Hz Other (Without connector) 50 60 50 60 4 50 60 5 6 7 50 60 9 Option Thread
60 Hz 200 VAC 50/60 Hz 110 VAC 50/60 Hz 220 VAC 50/60 Hz 24 VDC T -With conduit terminal TS -With conduit terminal and surge voltage suppressor TL -With conduit terminal and light TZ -With conduit terminal, surge voltage suppressor and light D -DIN terminal DS -DIN terminal with surge voltage suppressor DL -DIN terminal with light DZ -DIN terminal with surge voltage suppressor and light DO
1 Size 1 1 2 2 3 1 1/8 G Grommet 2 Size 2 2 3 3 4.5 2 1/4 *1 GS Grommet (With surge voltage suppressor) 3 Size 3 3 4.5 4 6 3 3/8 D DIN terminal (With surge voltage suppressor) Fitting type Face seal fitting/Compression fitting V Face seal tting S Compression tting DL DIN terminal with light (With surge voltage suppressor) Female thread type P Rc female thread N NPT female thread DO
Do not interchange the polarities to prevent the diodes or the switching elements from becoming burned. If lead wires are pre-connected, the red wire is + and the black wire is . Using the AC type: The AC type is not equipped with a surge voltage suppressor because the rectifier assembly prevents the generation of surge voltage. S is not available for AC.
Do not use the body A in a continuously rotating place. AQ Body B AS100P AS200P AS250P AS300P Model Rod and applicable tubing O.D. (Metric size) ASV 4 6 6 10 8 4 Flow rate [L/min (ANR)] It may damage the body A or fittings.
Do not use the air cylinder as an airhydro cylinder. This will result in oil leakage and damage the product. 2. Use a thin wrench when tightening the piston rod. 3. Check the mounting direction of the rod end nut (for male thread). Refer to Mounting Procedure on page 367 for details. 4. There are some changes in the dimensions and the specifications of this model from the current model.