Digital Flow Switch the operating conditions to calculate the product life, and do not exceed it.
Do not use the product in a place where it could be splashed by oils or solvents. 1. Do not drop, bump, or apply excessive impacts (100 m/s2) while handling. Although the body of the sensor may not be damaged, the internal parts of the sensor could be damaged and lead to a malfunction. 2.
Body Caution M5 hexagon socket head cap screw q M6 special screw (Do not disassemble.) Caution M6 special screw (Do not disassemble.) M5 hexagon socket head cap screw w Fig.1 Caution 1. Before disassembling, be sure to shut off the pressure supply, and then release the residual pressure. 2. After assembly, confirm that there is no fluid leakage.
Do not exceed the screw-in torque of 7 to 9 Nm when connecting the pipe to the switch. Exceeding these values may cause the switch to malfunction. 4. Do not use pressure sensors with corrosive and/or flammable gases or liquids. 5. Allow a sufficient margin of tube length in piping in order to prevent application of torsional, tensile or moment load to the tubes and fittings. 6.
Do not use in explosive atmospheres. 2. Do not use in locations subject to excessive vibration or impact. Impact resistance of this solenoid valve is 150 m/s2. Vibration resistance of this solenoid valve is 30 m/s2. 3. Do not use in locations where radiated heat will be received from nearby heat sources.
Note 9) External scratch marks and dirt are judged as good parts provided that they do not affect product performance.
Do not scratch or gouge the sliding portion of the piston rod and the guide rod. Damaged seals etc. will result in leakage or malfunction.
Do not use at temperatures (fluid or ambient temperatures) higher than the prescribed operating conditions.
Do not use at temperatures (fluid or ambient temperatures) higher than the prescribed operating conditions.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Error Name Error Display Error Type Troubleshooting Method Turn the power off and remove the output factor for the over current. Then turn the power on.
Claw 1 Claw 2 Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Error Name Error Display Error Type Troubleshooting Method [2] Turn the power off and remove the output factor for the over current. Then turn the power on.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. This function is to display error location and content when a problem or an error occurs. Error name Error display Error type Troubleshooting method Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids.
Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Preparation before setting (1)Supply pressure to the product. (2)Place the workpiece on the detection nozzle. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
When in a locked condition, do not apply a load accompanied by an impact shock, strong vibration or turning force, etc.
Do not loosen the cushion valve more than 2 turns from the fully closed state. Do not loosen it more than 2 turns because this could cause the cushion valve to be ejected. RE A B REC Caution CX Do not use an air cylinder as an air-hydro cylinder, because this could result in oil leakage. Do not twist the rod boot during installation.
Do not twist the valve seal 1.
Do not twist the valve seal 1.
Do not operate at pressures or temperatures, etc. beyond the range of specifications, as this can cause damage or malfunction. (Refer to specifications.) Contact SMC when using a fluid other than compressed air (including vacuum).
Make sure workpieces mounted on the table do not interfere with other workpieces or the facilities around the table. *3 Position after returning to origin *4 [ ] for when the direction of return to origin has changed *5 A switch spacer (BMY3-016) is required to secure auto switches.