JXCx-OMU0026

name Terminal Cable colour Terminal number number Brown 2 A B-1 Red 1 A A-1 Cable length [L] Orange 6 B B-2 Yellow 5 B A-2 8 8mNote) Green 3 COM-A/COM B-3 Blue 4 A 10mNote) COM-B/ A-3 (c) Shield B 15mNote) Cable colour Terminal number Brown 12 Vcc B-4 C 20mNote) Black 13 GND A-4 Red 7 A B-5 Note) Produced upon receipt Black 6 A A-5 Orange 9 B B-6 of order Black 8 B A-6 (Only "Robotic type

LEH_C

3 3 3 5 5 5 K K 5 (mm) NPN NPN 10 LECP6 ( PNP PNP 4 4 10 LECP1 1 LECP1 ( 1 NPN NPN 6 6 16 16 1P 1P PNP PNP 20 10 20 10 25 14 25 14 AN LECPA ( AP AN LECPA NPN NPN A A 32 22 32 22 AP PNP PNP B B (m) 40 30 40 30 C C 8 8 8 8 A A 1.5 1 1.5 1 10 10 B B 3 3 3 3 15 15 ( C C 5 5 5 20 20 F F 5 () () R R S S A B C / P.42 7.3 (NPNPNP) 12 - 2.1.3 3 10 2 5 1 4 7 6 9 8 1 2 3 4

OMR0032

Install a light shielding plate as a cover. position Modify the pulse and test the operation.

HRX-OM-W002

Model number Serial number Type and quantity of refrigerant How to read the serial number A R 001 April 2022 A R 001 Year Symbol Remarks Month Symbol Remarks Serial no. 4 R Repeated from O to Z in alphabetical order, with O for January and Z for December 2022 A 2023 B 5 S Repeat ed from A to Zin alphab etical order 2024 C 6 T Fig 1-1 Position of product label HRR Series 1.4 Product Label

NCG/CG1

D-M9 A/D-M9 AV (With indicator light) D-M9NAV V A B 9 M D A B 9 M D A N 9 M D D-M9PAV D-M9PA Auto switch part no.

Rotary Table

Thin shaft Position of rotational axis: Perpendicular to the shaft through the center of gravity diameter r a 2 2 r a I = m4 I = m 12 2. Thin rectangular plate 7. Cylinder Position of rotational axis: Parallel side b and Position of rotational axis: Through the center of diameter and gravity through the center of gravity a b a r 2 3 2 2 a r + a I = m 12 I = m 12 3.

AR Series Modular Type Regulator

Outlet pressure (MPa) Set point 0.2 0.15 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 Inlet pressure (MPa) 453 AR10-A to AR40-A Series Construction AR10-A AR20-A to 40-06-A t e t e q IN OUT IN OUT r r q w w Component Parts No.

Rotary Table

Cylinder Position of rotational axis: Parallel side b and Position of rotational axis: Through the center of diameter and gravity through the center of gravity a b a r 2 3 2 2 a r a I = m 12 I = m 12 3. Thin rectangular plate (Including 8.

PFxx-OMA1007

to "AMS20/30/40/60A-R/N/F#D" for dimensions other than "A" and "F".

Magnetically Coupled Rodless Cylinder

(The switch will stay ON all the time.) 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 5m or longer. 7. Do not use a load that generates surge voltage. If driving a load such as a relay that generates a surge voltage, use a contact protection box.

Stroke Reading Cylinder and Counter

In order to measure with a discrimination of 0.01 mm, a counter with a 4 times multiplication function (CEU5) is required.

CRQ2

gr ot ey R K Using the Body as a Flange The body's L dimensions are shown in the drawing on the right.

Cylinder with lock

Pneumatic circuit W a r n i n g Use the pneumatic circuit which applies balance pressure to the both sides of the piston when locking.

SY3000/5000/7000/9000 Series (Pilot Valve:V100)

screws a.

Cylinder with lock

Pneumatic circuit W a r n i n g Use the pneumatic circuit which applies balance pressure to the both sides of the piston when locking.

Cylinder with lock

Pneumatic circuit W a r n i n g Use the pneumatic circuit which applies balance pressure to the both sides of the piston when locking.

7ND9071en

Check using a feeler gauge that the clearance between the position indicator (109) and the electronics cover is 1 mm. 7 ND90 71 en 17 N O I T A C O L S U O D R A Z A H N O I T A C O L S U O D R A Z A H N O N ND9000H Valve Positioner Position Transmitter X300 Ui (Vmax) = 28 V Ii (Imax) = 120 mA Pi (Pmax) = 1 W Li = 53 uH Ci = 22 nF Ex i Barrier + 1 Uo (Voc) 28 V Io (Isc) 120 mA Po 1 W

CL

If there is a risk of contact, provide safety measures such as a cover or a system that uses sensors that will activate an emergency stop before contact is made. 2. Use a balance circuit in which lurching of the piston is taken into consideration.

Compact

1 t q r e A A B !6 @3 @6 @5 @4 @6 @2 @4 @5 @1 i y u C-C A-A !8 !3 B @7 !2 C w !7 C !5 !0 o Motor option: With lock !3 !1 !2 @0 !9 Component Parts Component Parts No. Description Material Note 1 Body Aluminum alloy Anodized No.

VG342

Flow Characteristics With DIN terminal block Port size Flow characteristics With terminal block 1 2 (P A) b Cv C [dm 3/(sbar)] 2 3 (A R) b Cv C [dm 3/(sbar)] 2 1 (A P) b Cv C [dm 3/(sbar)] 3 2 (R A) b Cv C [dm 3/(sbar)] 1/2 3/4 26 38 0.38 0.30 7.0 9.8 27 38 0.37 0.32 7.4 9.8 27 40 0.36 0.22 7.3 9.8 25 40 0.37 0.20 6.8 9.6 Port size Effective area (mm2) 2 3 (A R) 1 2 (P A) Ground