Regulator for 2 MPa ARX 20 Do not subject the gauge to impacts, such as dropping, during transportation and mounting. This can cause loss of indication accuracy. 2. Do not use in locations with high temperature and humidity. This can cause malfunction. 3. When screwing the pressure gauge into place, be sure to apply your wrench on the square wrench flats.
Before piping and screwing in couplings, please make sure that sludge trom pipe threading and sealing materials do not go into the pipe. When seal tape is used, tape winding should be done so that 2 threads are left untaDed on the end.
(Default value : 100%2.00MPa) (Note3) Do not input the signal as like output the pressure of more than 100%. Please use in a range of rating. (Note4) The difference between F_1 and F_2 is adjustable in a range of 10% of the rated value. (Note5) The adjustment like making the relation of F_1 > F_2 is not available.
BRAZIL SMC Pneumaticos do Brazil Ltda. CHILE SMC Pneumatics (Chile) S.A. PERU SMC Corporation Peru S.A.C. VENEZUELA SMC Neumatica Venezuela S.A. OCEANIA AUSTRALIA SMC Pneumatics (Australia) Pty. Ltd. NEW ZEALAND SMC Pneumatics (N.Z.) Ltd. EUROPE AUSTRIA SMC Pneumatik GmbH (Austria) BELGIUM SMC Pneumatics N.V./S.A.
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 37
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 38
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not cut the tube with cutting pliers, nippers, scissors, etc.) 2. Grasp the tube, then slowly push it until it comes to a stop. 3. Then, pull it back gently to make sure that it does not come out.
Do not allow the weight of piping to lie directly on air dryer. 4. Do not connect a tube smaller than the port size to the inlet side. In particular, when using a resin tube, make sure that the size would not be smaller than the port size.
VQC1000/2000 series valves do not come with mounting screws or gaskets. For VQC4000/5000 series valves, when a valve is ordered individually, it comes with a mounting screw but no gasket. VQC1000/2000 series valves do not require separate mounting screws as there are clamp screws built into the manifold.
VQC4000/5000 series valves do not have common polarity.
② For manifolds with serial transmission kits, whether the valves are positive common or negative common depends on the type of protocol. For VQC1000/2000 series valves, install valves with the same common specification as the common specification of your protocol.
Do not restrict the flow rate by plugging or mounting a speed controller to the exhaust port.
In addition, SY7120 series valves do not come with a gasket because they are the equivalent of existing SY7000 series body ported valves.
The SY7000 series body ported valve gasket assembly part number is “SY7000-GS-1.”
Do not tighten or loosen the release bolts excessively. Also, do not tighten them with a pneumatic or electric screwdriver because it may damage internal parts of the product.
For further details, refer to the excerpts from the MWB series “Specific Product Precautions” below.
However, unlike KS and KX series rotary One-touch fittings, they do not rotate with low friction. Do not use the product in a manner in which the connected tube swings or rotates with respect to the fitting.
PF2D series: Pure water and liquids that do not corrode or permeate Teflon (Refer to the list of applicable fluids in the catalog.)
LFE series: Fluids that do not corrode the materials of wetted parts (Refer to the list of applicable fluids in the catalog.)
However, new VX2 (with a white coil) series valves do not have mounting holes on the bottom surface of the body, so brackets cannot be retrofitted.
If the part number is “VX2□□□□XNB,” a bracket can be retrofitted because it has a mounting hole on the bottom surface of the body.
Note) 1/2 port size VX2 series valves do not have an option with brackets as standard.
Please contact us for the latest version.sales@ocaire.com, MANIFOLD, 16-STA, VALVE, VV3K* MANIFOLD VK 3-PORT, NJ, VV3K* BASE MT 1/8, .59516 lb
Please contact us for the latest version.sales@ocaire.com, MANIFOLD, 16-STA, VALVE, VV3K* MANIFOLD VK 3-PORT, NJ, VV3K* BASE MT 1/8, .30684 lb
The SY is available in body ported or base mounted styles, and can be used individually or manifold mounted.Plug-in metal base (IP20) , Manifold for EX510 Gateway-type serial transmission system , Side or bottom ported , Side ported available with external pilot , Available with one-touch fittings, MFLD ASSY, 16-STA (SY), VALVE, SS5Y5 MANIFOLD SY5000, 2J, SS5Y5 NO SIZE RATING, 1.58400