PFxx-OMA1007 to "AMS20/30/40/60A-R/N/F#D" for dimensions other than "A" and "F".
(The switch will stay ON all the time.) 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 5m or longer.
In order to measure with a discrimination of 0.01 mm, a counter with a 4 times multiplication function (CEU5) is required.
gr ot ey R K Using the Body as a Flange The body's L dimensions are shown in the drawing on the right.
Pneumatic circuit W a r n i n g Use the pneumatic circuit which applies balance pressure to the both sides of the piston when locking.
Pneumatic circuit W a r n i n g Use the pneumatic circuit which applies balance pressure to the both sides of the piston when locking.
Pneumatic circuit W a r n i n g Use the pneumatic circuit which applies balance pressure to the both sides of the piston when locking.
Check using a feeler gauge that the clearance between the position indicator (109) and the electronics cover is 1 mm. 7 ND90 71 en 17 N O I T A C O L S U O D R A Z A H N O I T A C O L S U O D R A Z A H N O N ND9000H Valve Positioner Position Transmitter X300 Ui (Vmax) = 28 V Ii (Imax) = 120 mA Pi (Pmax) = 1 W Li = 53 uH Ci = 22 nF Ex i Barrier + 1 Uo (Voc) 28 V Io (Isc) 120 mA Po 1 W
If there is a risk of contact, provide safety measures such as a cover or a system that uses sensors that will activate an emergency stop before contact is made. 2. Use a balance circuit in which lurching of the piston is taken into consideration.
1 t q r e A A B !6 @3 @6 @5 @4 @6 @2 @4 @5 @1 i y u C-C A-A !8 !3 B @7 !2 C w !7 C !5 !0 o Motor option: With lock !3 !1 !2 @0 !9 Component Parts Component Parts No. Description Material Note 1 Body Aluminum alloy Anodized No.
Flow Characteristics With DIN terminal block Port size Flow characteristics With terminal block 1 2 (P A) b Cv C [dm 3/(sbar)] 2 3 (A R) b Cv C [dm 3/(sbar)] 2 1 (A P) b Cv C [dm 3/(sbar)] 3 2 (R A) b Cv C [dm 3/(sbar)] 1/2 3/4 26 38 0.38 0.30 7.0 9.8 27 38 0.37 0.32 7.4 9.8 27 40 0.36 0.22 7.3 9.8 25 40 0.37 0.20 6.8 9.6 Port size Effective area (mm2) 2 3 (A R) 1 2 (P A) Ground
Note 3) A particulate generation test has been conducted in a vacuum environment of 10-Pa. a t e l u g c 2 Stainless steel linear guide & low particulate generation vacuum grease e i t n r a e p r a 0.0 10 0 20 10 w t i o o n L Operation cycles a t e l u g c e 1 i t n r a e Particulate generation from the linear guide unit has been reduced with the use of a stainless steel linear guide and
9 qo r !3 @1 e #1 #4 @0 !8 t @3 B' CL !7 N@4 CL1 A' A A' A MLGC CNG B MNB @5 !5 CNA CNS 20, 25: 50 stroke or less Over 100 stroke CLS CLQ Extension locking (Type F) Retraction locking (Type B) MLGP N#2 u #6 y @2 u #6 #2 y #5 @2 i i RLQ MLU ML1C D-X Section B-B' Section B-B' 20Section A-A' !6 !6 Section A-A' Data Component Parts Description Material Note No. !7 !8 !
Note 2) Since the table is made of a magnetic substance, it could become magnetized if touched by a magnet, etc.
9 qo r !3 @1 e #1 #4 @0 !8 t @3 B' CL !7 N@4 CL1 A' A A' A MLGC CNG B MNB @5 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com !
When rod end female thread is used, use a thin wrench when tightening the piston rod. 712 Series CM2R-Z 10-/1121-/2220, 25, 32, 40 Direct Mount Cylinder RoHS How to Order Clean series 10 11 Relief type Vacuum suction type 10 C D M 2 R A 40 150 F Z M9BW 21 C D M 2 R A 40 150 F Z M9BW Mounting Number of auto switches Rod end thread A B Bottom Front Nil S n 2 pcs. 1 pc. n pcs.
In combination with L/R keys, this key drives the actuator at high speed during a JOG operation. UP Moves downward for item selections. Also used to decrease values for data entry. DOWN Moves to the left for item selections. Also used to move a numerical value place to the left for data entry. It drives the actuator to the end side during a JOG operation.