3/5 Port Solenoid Valve Metal Seal/Rubber Seal Base Mounted VQZ1000/2000/3000 Piping direction can be changed on VQZ100. Fitting ass'y It's possible to change from side to top porting and vice versa.
Add the "" symbol at the beginning of part numbers for solenoid valves, etc., to be mounted.
(The additional rotation should be doubled to 1/2 when using the universal elbow, universal tee, etc. which have two gaskets.) If tightened too much, thread portion may be damaged and gasket may be deformed. This will cause air leakage.
Surge pressure must be under the max. operating pressure. Note2) Suffix S to part number if sealant is desired.
Note 2) Can be mounted on L kit only. For other kits, order E type control unit.
O~ 0.2 0.3 04 05 0.6 O~ 08 09 00 1000 2000 Auto drain Flow rate /min (ANR) Inlet pressure MPa (Float type normally open) AW4001-04 AW4001 -04 OOrain line should be Bmm or more and should be less than Sm. Be sure not to have any upward turns in the drain line which would prevent drainage. -0.25 H---''t' .:c ' +-+-t---+--r--.
RE A B Model Recommended Speed Controller REC Model Elbow type Straight type In-line type CX REC20 AS2201F-01-06-X214 AS2301F-01-06-X214 AS2001F-06-X214 REC25 AS2201F-01-06-X214 AS2301F-01-06-X214 AS2001F-06-X214 CY REC32 AS2201F-01-06-X214 AS2301F-01-06-X214 AS3001F-08-X214 REC40 AS3201F-02-08-X214 AS3301F-02-08-X214 AS3001F-08-X214 MQQ M Courtesy of Steven Engineering, Inc.-230 Ryan Way
Note 2) Will be manufactured upon receipt of order.
5 Caution Be sure to read before handling.
For auto switches (except the M9lV), when the total thickness of shims and a workpiece is over 2 mm, the auto switch may not be adjusted to the most sensitive position.
Cut the multi-tube holder depending on number of tubes to be connected.
IN side, OUT side 4 10 22 20 22 30 30 50 30 75 39 75 39 Recommended air flow Tubing size Model ZFB100-04 ZFB100-06 ZFB200-06 ZFB200-08 ZFB300-08 ZFB300-10 6 6 8 8 10 Unrestricted 360 piping tube mounting. The connector for the IN side is a universal joint type that enables a tube to be connected in any direction within 360.
If the release bushing is not pressed down sufficiently, there will be increased bite on the tubing and it will become more difficult to pull it out. (3) When the removed tubing is to be used again, cut off the portion which has been chewed before reusing it.
Connection of Lead Wire If the manual override is turned by 180 clockwise and the mark is adjusted to 1, then pushed in the direction of an arrow (), it will be locked in the ON state. If the manual override is turned by 180 counterclockwise and mark is adjusted to 0, locking will be released and the manual override will return.
If the socket is to be re-used, reposition the hook again.
M Weight (g) AS AS221F-U01-23 AS221F-U01-04 AS221F-U01-06 AS221F-U01-08 AS221F-U01-10 AS221F-U02-04 AS221F-U02-06 AS221F-U02-08 AS221F-U02-10 AS321F-U02-06 AS321F-U02-08 AS321F-U02-10 AS321F-U02-12 AS321F-U03-06 AS321F-U03-08 AS321F-U03-10 AS321F-U03-12 AS421F-U04-10 AS421F-U04-12 3.2 4 6 8 10 4 6 8 10 6 8 10 12 6 8 10 12 10 12 7.8 8.9 11.0 15.2 18.5 8.9 11.0 15.2 18.5 11.0 15.2 18.5 20.9
Type Metric size Inch size Elbow Universal 2 3 1/8" 5/32" 3/16" 1/4" 5/16" 3/8" 1/2" 01 23 3.2 4 6 8 10 12 03 05 07 09 11 13 04 06 08 10 12 Control type Meter-out Meter-in 0 1 Use 1/8" tube.
Universal type Symbol Elbow type Flow Direction Symbols on Body Meter-out type Meter-in type Applicable tubing O.D. 2 Indication symbol Symbol Caution Be sure to read before handling. Refer to front matter 56 for Safety Instructions and pages 468 to 471 for Flow Control Equipment Precautions.
The write prohibited setting parameter (Fn010) must be set to Write permitted (P.0). The main circuit power supply must be ON. All alarms must be cleared. The hardwire baseblock (HWBB) must be disabled. The servomotor power must be OFF. There must be no overtravel. The test without a motor function must be disabled (Pn00C.0 = 0).
If the cylinder is to be bottom mounted, bypass ports should be provided for the guide rods.