SZ3000 Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. Confirm the specifications in the main section of this catalog. 4. A protective cover, etc. should be used to shield valves from direct sunlight. 5.
Do not use in atmospheres where the valve is in direct contact with corrosive gases, chemicals, salt water, water or steam. 2. Do not use in locations subject to vibration or impact. Confirm the specifications in the main section of the catalog. 3. Use a protective cover, etc., to shield valves from direct sunlight. 4.
Do not apply vibration to the switch.
Do not make any upward angles in drain line.
Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. The product is not designed to be explosion proof. Do not Do not use the product in a place where static electricity is a problem. Otherwise failure or malfunction of the system can result.
Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. The product is not designed to be explosion proof. Do not Do not use the product in a place where static electricity is a problem. Otherwise failure or malfunction of the system can result.
NO YES Do you have any problem, even if it might run over the target position? (Overrun) NO Do you have any problem, although an error might occur if it is set to be (number of trial again = 0) in order to prevent from doing a trial again when positioning is done at the outside of the range? During the positioning operation, there may be the case it needs to do overruns or trials again.
NO YES Do you have any problem, even if it might run over the target position? (Overrun) NO Do you have any problem, although an error might occur if it is set to be (number of trial again = 0) in order to prevent from doing a trial again when positioning is done at the outside of the range? During the positioning operation, there may be the case it needs to do overruns or trials again.
Series: 3 (VFA3000), Manifold: 30 (VFA1000 P,R Port Size: 1/8; VFA3000 P,R Port Size: 1/4), Stations: 04, Type: 1 (Common Exhaust), Thread: 00N (NPT)
Series: 5 (VFA5000), Manifold: 20 (P.R Port Size 3/8), Stations: 04, Type: 1 (Common Exhaust), Thread: 00N (NPT)
Type: 20 (Common SUP/Common EXH), Stations: 04, Bracket: None, Thread: 00N (NPT)
Type: 20 (Common SUP/Common EXH), Stations: 04, Bracket: F (w/Bracket, Not Mounted), Thread: 00N (NPT)
Do not ground to water pipe, gas tube or lightening rod line. 7. Do not connect too many wires to the same outlet, which could results in heat generation and fire. 8. Do not retrofit the wiring of the dryer and the power supply line. 9.
Do not use compressed air that contains chemicals, synthetic oils including organic solvents, salt or corrosive gases, etc., as it can cause damage or malfunction. 4. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 5.
CAUTION Air combination Do not drop or apply impact during transportation or installation. It will cause damage to the product or operation failure. Do not install in areas of high humidity or high temperature. The product cannot be used in the horizontal or upward directions outside of the specifications.
Do not use valves in such environments where corrosive gases, chemicals, or brine or water or steam is airborne, or where valves can be directly exposed to any of those. 2. Do not use in locations influenced by vibrations or impacts. 3. This vacuum regulator always uses atmospheric air, therefore, do not use in dusty environments. 4.
Bore size Applicable series 02 03 04 06 10 12 14 20 Note 1) AS800 is available as special.
Applicable model t ZH15DA-09-N03-11 ZH15DA-N02-N03-N03 2 Minimum C Factor of a Supply Valve Model C[dm3/(sbar)] ZH05A 0.12 ZH07A 0.23 ZH10A 0.47 ZH13A 0.80 ZH15A 1.06 ZH18A 1.53 ZH20A 1.88 ZH18DA-11-N03-13 ZH18DA-N03-N03-N03 1 ZH20DA-10-04-12 ZH20DA-03-04-04 ZH20DA-11-N04-13 ZH20DA-N03-N04-N04 t 2.