Series 10-SYJ3000/5000/7000 Rubber Seal 4/5 Port Solenoid Valve (Coil temperature: 20C, at rated voltage, without surge voltage suppressor) Note 2) Impact resistance: No malfunction occurred when it was tested in the axial direction and at right angles to the main valve and armature in both energized and de-energized states once for each condition.
Note Conductor resistance /km, 20C 65 or less 1.5 m 3 m 5 m AXT100-DS25-015 Cable 25 cores x 24AWG AXT100-DS25-030 Withstand limit VAC, 1 minute 1000 AXT100-DS25-050 For other commercial connectors, use a 25 pin type with female connector conforming to MIL-C24308. Insulation resistance Mkm, 20C 5 or less Note) The minimum bending radius of the D-sub connector cable is 20 mm.
(Coil temperature: 20C, at rated voltage) 10-SY3000 10-SY7000 With light/surge voltage suppressor Response time (ms) (at the pressure of 0.5 MPa) With light/surge voltage suppressor Response time (ms) (at the pressure of 0.5 MPa) Actuation type Without light/surge voltage suppressor 12 or less Actuation type Without light/surge voltage suppressor 31 or less Type R, U Type S, Z 12 or less
(Coil temperature: 20C, at rated voltage, without surge voltage suppressor.) Note 2) Impact resistance: No malfunction occurred when it was tested in the axial direction and at right angles to the main valve and armature in both energized and de-energized states once for each condition.
The resistance of the solenoid valve is R 20 + 278 3% Ohm at 68F (20C). Do not bend or pull cables repeatedly. T4 Maximum surface temperature 275F (135C) Temperature class Hazardous Locations Specifications Terminal type (TT) L-type plug connector (L) LL-type plug connector (LL) Warning Electrical entry Note) 1.
Maximum Flow Capacity of the Compressor Intake Condition under Rated Conditions Model AFF70D AFF80D AFF90D Maximum flow capacity/Compressor intake condition*2 [m3/min] 7.3 11.5 15.1 *1 Flow at 20C, atmospheric pressure, and 65% of relative humidity *2 32C, flow rate when converted to atmospheric pressure *3 Filtration efficiency for the conditions below in addition to the rated conditions
Burst pressure Note) Min. bending radius (mm) 24 Burst pressure (MPa) Operating temperature Material 20C to 60C Nylon 12 Note) The value at temp. of 20C and with O.D. variable rate 10% max.
(mm) ASG32F-01 4 ASG42F-02 6, 8 ASG52F-03 6 ASG62F-04 Sealant: Special FKM Seat ring: Stainless steel 303 8 12 4, 6 8, 10 10, 12 460 920 790 1580 100 180 230 390 Flow rate (l/min (ANR)) Controlled (free) flow 7 14 12 24 1.5 2.7 3.5 6 Effective area (mm2) Applicable tubing materials Note) Flow rate is measured at 0.5 MPa and 20C.
(at 20C) Data 10-12-9 9 Series CEP1 Proper Auto Switch Mounting Position Weight (Without mounting bracket/connector) (kg) Regarding dimensions for the proper auto switch mounting position (at stroke end), refer to page 1012-16.
Standard condition : Air in a temperature state of 20C, absolute pressure 0.1 MPa (= 100 kPa = 1 bar), relative humidity 65%. It is stipulated by adding the (ANR) after the unit depicting air volume.
Subsonic flow : Flow greater than the critical pressure ratio Standard condition : Air in a temperature state of 20C, absolute pressure 0.1 MPa (= 100 kPa = 1 bar), relative humidity 65%. It is stipulated by adding the (ANR) after the unit depicting air volume.
Residence time of water at 20C is 5.5 x 10-6 sec, whereas at 150C, it is 2.8 x 10-8 sec, or about 200 times shorter. The objective of baking is to exhaust water with long adsorption residence time more quickly. XVD Surface leakage This leakage occurs between surfaces of the sealing and the seal material.
Residence time of water at 20C is 5.5 x 10-6 sec, whereas at 150C, it is 2.8 x 10-8 sec, or about 200 times shorter. The objective of baking is to exhaust water with long adsorption residence time more quickly. XVD Surface leakage This leakage occurs between surfaces of the sealing and the seal material.
(Variation: 10%) *7 The value when there is an ambient temperature of 20C and when the rated voltage is applied. The value depends on the ambient environment.
In-line Air Filter RoHS Operating pressure range 100 kPa to 1.0 MPa (20C) Both positive pressure and vacuum pressure can be used with one unit! 5 m Filtration OUT IN 100 kPa 1.0 MPa Positive pressure e.g.)
Standard equipment AMF 1/2B 3/8B 1B (3) Accessory 11/2B SF Note 1) ANR indicates the flow rate converted to the value at 20C under the atmospheric pressure and the state of relative humidity 65%. Note 2) Based on discharge rate and discharge temperature (70C) of screw type compressors. Note 3) The accessories should be mounted by user.
At this time correction factor line becomes A . coefficient (1) To get correction factor of 1.35 use ambient temperature correction factor A at 20C. (2) (3) To get outlet air temperature divide 38.5C from (1) by 1.35 from (2).
Note 1) ANR indicates the flow rate converted to the value at 20C under the atmospheric pressure and the state of relative humidity 65%. Note 2) The accessories should be mounted by user.
(at 20C) Data 10-12-9 9 Series CEP1 Proper Auto Switch Mounting Position Weight (Without mounting bracket/connector) (kg) Regarding dimensions for the proper auto switch mounting position (at stroke end), refer to page 1012-16.
(mm)Thickness (mm)BundleStraight pipeColorApplicable fluidMax. operating Note 1)pressure (at 20C)Burst pressure (at 20C)Note 2)radius (mm)Max. operating temperature (Fixed use)MaterialBasic diameterTolerance10 m20 m50 m100 m50 Ft. (16 m)100 Ft. (33 m)2 mInch sizes (Series TIL)TIL053/16andquot;3/16andquot; x 1/8andquot;4.75?0.10.8?0.08?