SMC Corporation of America
Elite Part Number Search
Search Results "HRS200-AN-46-AS"

OK OK Model determination Note 1) Stroke adjustment with either a bumper bolt or adjustment bolt is considered as an intermediate stop. Note 2) When an intermediate stop is performed with an external stopper, consider the dynamic load as shown below.

(-XC6) Caution Other specifications are the same as the standard model. Dimensions q Do not use the air cylinder as an air-hydro cylinder. This will cause an oil leak. w Install without twisting the bellows. If the cylinder is installed with its bellows twisted, it could damage the bellows.

Smooth operation and longer life from an oil containing slide bearing. Rotary seal A special rotary seal minimizes friction while providing an excellent seal.

Note) When placing an order for body ported solenoid valve as a single unit, mounting bolt for manifold and gasket are not attached. Order them separately, if necessary. (For details, refer to page 4-4-11.) 4-4-6 7 3 Port Pilot Operated Solenoid Valve Rubber Seal Series SYJ300 Construction (A) 2 (A) 2 N.C.

However, when mounting a blanking part to a valve, place an order for a separate gasket (SYJ700-5-3) when placing an order for the valve. When using the SYJ700-10-1A, a gasket for this blanking plate assembly can be used as a gasket for the valve as well.

As the standard electrical wiring specifications, double wiring (connected to SOL. A and SOL. B) is adopted for the internal wiring of each station for 8 stations or less, regardless of valve and option types. Mixed single and double wiring is available as an option. For details, refer to page 2-4-29.

Parameter Setting 46 I/O Map 46 Diagnostic 46 Accessories 46 Precautions before mounting 47 -2No.EX-OMN0038-C Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.

The flatness of the mounting surface may not be maintained, which would cause an increase in sliding resistance.

Air Cylinders Applicable for use in an environment with water splashing such as food processing and car wash equipment, etc.

Air Cylinders Applicable for use in an environment with water splashing such as food processing and car wash equipment, etc.

Use the air dryer with an ambient temperature lower than 40C. Avoid installation on machines for transporting, such as trucks, ships, etc. Avoid locations which experience sudden pressure/flow rate changes.

Simple Specials System AR AL Short lead times This system enables us to respond to your special needs, such as additional machining, accessory assembly, or modular unit, and deliver such special products as quickly as standard products.

How to Order Type 46 (5 Port/Base mounted) Applicable solenoid valve SYJ340SYJ343SS5YJ3 46 05 M5 Type 46 Type S46 ( ) Single solenoid coil is on same side as the A, B port. M5 x 0.8 R1 R2 port Applicable blanking plate assembly SYJ3000-21-2A Stations Valve mounting direction 02 2 stations Single solenoid coil is on opposite side as the A, B port.

52 46 55 63 69 S 33 36 40 46 50 52 Z 46 52 56 65 73 79 6 10 16 20 25 32 7 9 12 16 20 24 6 depth 4.8 6 depth 5 7.6 depth 6.5 9.3 depth 8 9.3 depth 9 11 depth 11.5 5 7 Free Mount Cylinder Double Acting, Single Rod Series CU Proper Auto Switch Mounting Position (Detection at stroke end) and Its Mounting Height D-A9 D-M9 D-F9W 22 (24.5) ( ): Denotes the values of D-A93.

As a result, the inside of the bowl q is shut off from the outside air. Therefore, even if there is an accumulation of condensate in the bowl q, it will not drain out.

If using in an environment that is exposed to water splashes, please take measures such as using a cover. If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent, even for a short time, it may be adversely affected (damage, malfunction etc.).

The purpose of an air cushion is not to reduce the speed of a piston as it nears the stroke end.

The product can be used at an ambient temperature as low as 20C, but take measures to prevent the solidification or freezing of impurities, etc. 2. When using for water, etc. in a cold area, devise a means to prevent freezing, such as draining the water from pipelines after stopping supply and exhaust water for a pump or other device.

2 q q AS y !3 w y t AS-FE w i t KE o AS-FG AS-FG i !0 u AS-FP !0 o e AS-FM !4 u Meter-in type Meter-out type AS-D e Seal method: Face seal For G thread AS-T Meter-in type Meter-out type ASP !1 ASN r !2 AQ q w ASV y t AK i VCHC o ASR ASQ !0 u !5 e Meter-out type Meter-in type Component Parts No.