VM : One-touch fitting 1(P): Male thread 2(A): One-touch fitting 1(P): One-touch fitting 2(A): Male thread 1(P): Male thread 2(A): Male thread 2(A) 2(A) 2(A) 2(A) Applicable tubing O.D.
Use a soft cloth to remove stains.
The Pressure switch is a UL approved product only if it has a mark on the body. A pressure sensor of stainless steel diaphragm is used for this product.
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Warning 1.
Bracket A (Part No.: ZS-50-A) Bracket B (Part No.: ZS-50-B) -15No.PS-OMV0009-E Mounting with orifice : Tighten the orifice to a torque of 1.50.1 Nm. Orifice (Part No.: ZS-48-A) -16No.PS-OMV0009-E Piping Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm.
Bracket A (Part No.: ZS-50-A) Bracket B (Part No.: ZS-50-B) -14No.PS-OMV0004-H Piping Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm. Piping specification: -F02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting.
r p g n i t a r e p o . x a M ) 7 . 0 ( 0 0 1 g i s p * e g n a r g n i t a r e p o l a i t n e r e f f i d e r u s s e r P ) a P M ( ) 6 . 0 ~ 1 . 0 ( 0 9 ~ 5 1 e g n a r . p m e t g n i t a r e p O F 0 4 1 ~ 0 4 t n a c i r b u l d e d n e m m o c e R ) 2 3 G V O S I ( 1 # l i O e n i b r u T l w o B e t a n o b r a c y l o P T L A N k n a T d e e F o t u A 5 T L A N 1 * S 1 5 T L A
Bracket A (Part No.: ZS-50-A) Bracket B (Part No.: ZS-50-B) -13No.PS-OMW0002-C Piping Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm. Piping specification: -F02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting.
Series 25 19 dB (A) Page 5-10-4 VEX AN101-01 AN110-01 AN120-M5 AN120-M3 BC sintered body type Ideal for the exhaust of a compact valve or pilot air. 16 dB (A) 21 dB (A) 18 dB (A) 13 dB (A) 100 m AN Page 5-10-5 Silencers Exhaust Cleaner 70 m AMC One-touch fitting connection type Can connect with One-touch fitting directly. 25 dB (A) 30 dB (A) It differs depending upon the model.
When a system hazard can be expected due to a drop in vacuum pressure caused by power loss or vacuum pump trouble, install a safety circuit and configure the system so that it can avoid the danger. 2. When a system hazard can be expected with a malfunction of the vacuum regulator, install a safety circuit and configure the system so that it can avoid the danger. 1.
(A,MR~~N '(lmjQ' . 180 600 1100 1190 [Ereo flaw) Effettive ~IOnal 11.6 17 2.9 5.2 18.4 5.4 9.3 'ttrea mm 2 . N01e} The iMicaled 110w rate values are al a pressure 01 O.5MPa and a temperature 01 20 Q C. 1 Speed Controller 5 .
ANm0m0-KMmm 5.2-4 40dB(A): High Noise Reduction Silencer Series ANA1 A high noice reduction style silencer keeps the noise level inside a plant below 85dB(A).
high quality 0.01 micron oil removal coalescing filter with a built in prefilter.
Description No. 2 Common IN Individual IN Common IN Individual IN Bonnet Polyacetal Regulator NARM2500-A-N02 NARM2500-B-N02 NARM3000-A-N03 NARM3000-B-N03 9 Regulator 1 Component Parts 10 End plate R 1 No.
2 2 S () N 3 M SI4 3 (SI) 4L/min,L A NPN(2) B PNP(2) C NPN(1)+(15V) D NPN(1)+(420mA) E PNP(1)+(15V) F PNP(1)+(420mA) G NPN(1)+5 H PNP(1)+5 5 L 6INOUT () 10 25 50 11 01 Rc1/8 02 Rc1/4 N01 NPT1/8 N02 NPT1/4 F01 G1/8 F02 G1/4 C4 4(5/32") C6 6 C8 8(5/16") N7 1/4 -10No.PF-OMJ0005CN-I 1 W Z (2 m) (2 m) + () 2 R S () () T V () () A A B B -11No.PF-OMJ0005CN-I IN OUT X693 IN OUT 73
Contact P/A if the product will be used in an application with a high frequency of operation. 1. Do not subject the gauge to impacts, such as dropping, during transportation and mounting. This can cause loss of indication accuracy. 2. Do not use in locations with high temperature and humidity. This can cause malfunction. 3.
) ( ): Fluid: CO2 Calibration certificate Flow adjustment valve None With calibration certificate Nil A Nil S None Yes The certificate is written in English and Japanese. Other languages are available as specials.
Body Size: -, Thread: -, Port Size: -, Option: -, Attachment: -, Semi-Standard 1: -, Semi-Standard 2: -
Body Size: 40, Thread: NPT, Port Size: 1/2, Option: for Sizes 20, 25, 30, 40 Round Type Pressure Gauge w/Limit Indicator; for Size10: Round Type Pressure Gauge w/o Limit Indicator, Attachment: 3-Port Valve for Residual Pressure Release, Semi-Standard 1: Lubricator w/Drain Cock, Exhaust Port, Semi-Standard 2: R + W + Z