XM, XY x 10-11 (FKM) 1.3 x 10-9 CYV Q1 R1 R2 R3 S1 T1 U1 Kalrez 4079 SS592 SS630 SSE38 1232-70 3310-75 1.3 x 10-10 (FKM) Note 1) Values at ambient temperatures, excluding gas permeation.
Refer to pages 11 to 13 for cylinders with auto switches.
The tightening torque should be approximately 0.05 to 0.1 Nm. 8-17-11 11 Series CYP Specific Product Precautions 1 Be sure to read before handing. Operation Handling Caution Caution 1. Open the inner package of the double packaged clean series inside a clean room or other clean environment. 2.
-X 20Data Table (1) 100 Total operation cycles (10,000) 50 40 30 20 10 100 200 300 400 500 700 1000 Stroke (mm) Inner Cover Holding Screw Tightening Torques [Nm] Tightening torque Model Screw size CYV15 0.3 M3 x 0.5 CYV32 2.45 M6 x 1 Plate Stroke adjustment screw (inner cover) Hexagon wrench Inner cover holding screw direction + direction 8-18-11
(PCI) 12 11 10 9 8 Joint bracket Bracket for joining to adjacent units. 6 3 1 5 Connector (PCI) Connects the cable of the handheld terminal. 7 4 2 Direct mounting (1)When joining six or more units, fix the middle part of the complete EX600 unit with an intermediate reinforcing brace (EX600-ZMB1) before mounting using 2-M4x5 screws. Tightening torque: 0.7 to 0.8 Nm.
Settings1 Intermediate reinforcing brace (EX600-ZMB2) 10 to 57 Hz: constant amplitude 0.75 mm p-p 57 to 150 Hz: constant acceleration 49 m/s2 Mode Diagnostic size set for the input Content 2 Vibration resistance NOTE for 2 hours each in direction X, Y and Z respectively (De-energized) 0 OFF 0 byte Input data only (default setting) 147 m/s2 3 times each in directions of X, Y and Z respectively
(PORT2) 11 The power supply for output is properly. Green ON PWR(V) The power supply voltage for output is below 19 VDC. (When diagnostic parameter is enabled) Red ON Assembly Either of the following conditions are detected: The unit has not been configured correctly. The PLC is idle state.
Please keep this manual handy for future reference. 11 Connect the M12 connector cable.
PWR(V) 11 Connect the M12 connector cable. The M12 SPEEDCON connector connection method is explained below. (1)Align mark B on the metal bracket of the cable connector (plug/socket) with mark A. 7 10 8 SF Displays the system status. 1 9 BF Displays the communication status. (2)Align with mark C on the unit and insert the connector vertically.
Impact resistance of the product is 150[m/s2]. Vibration resistance is 30[m/s2]. Avoid applying vibration exceeding the allowable value to the product. Mounting Warning 1. Install a stop valve on the supply pressure side of the impact blow valve. This will be an emergency stop in case of leakage or breakage. 2. Refer to How to mount a Nozzle on page 4 for assembling the nozzle. 3.
Nm JMHZ2-16D M3x0.5 0.59 17 - MOTOMAN-HC10 M6x12 6.3Nm 18 - M6x23 6.3 Nm M4x10 1.0Nm 19 - M8 M8 M8-MOLEX S1 S2 M4x8 1.0Nm 20 - (M4x6) (M4x6) 1.0Nm P175-2. M3x7 0.59Nm 21 - 0.7mm 22 - 5-3 1. 2. 3. 4. 1.() 2. 5m 3. 4. 5 5-4. 1.
Rail mounting type Electrical entry Grommet Oil proof vinyl heavy insulation cable 3.5 0.14 mm2 4 cores 3 m With one e-con connector Note) Lead wire Impact resistance 980 m/s2 Amplifier unit Insulation resistance 50 M (500 VDC) between lead wire and case Withstand voltage 1000 VAC for 1 min. between lead wire and case Ambient temperature 10 to 60 C Enclosure IP67 Weight 58 g (with connector
Hexagon socket head cap screw (M6 x 23) Max. tightening torque 5.2Nm M8-Molex Conversion cable * Either the robot side connector S1 or S2 can be connected.
(BUS OUT and PCI) 12 11 10 9 8 6 5 3 1 7 4 2 Direct mounting (1)When joining six or more units, fix the middle part of the complete EX600 unit with an intermediate reinforcing brace (EX600-ZMB1) before mounting using 2-M4x5 screws. Tightening torque: 0.7 to 0.8 Nm. DIN rail mounting (Available for series other than SY series.
Mounted on to unused connectors (BUS OUT and PCI). 12 11 10 9 8 6 5 3 1 7 4 2 Direct mounting (1)When joining six or more units, fix the middle part of the complete EX600 unit with an intermediate reinforcing brace (EX600-ZMB1) before mounting using 2-M4x5 screws. Tightening torque: 0.7 to 0.8 Nm. DIN rail mounting (Available for series other than SY series.
(BUS OUT and PCI) 12 11 10 9 8 6 5 3 1 7 4 2 Direct mounting (1)When joining six or more units, fix the middle part of the complete EX600 unit with an intermediate reinforcing brace (EX600-ZMB1) before mounting using 2-M4x5 screws. Tightening torque: 0.7 to 0.8 Nm. DIN rail mounting (Available for series other than SY series.
Auto preset (page 11) Automatically sets the pressure value. Although supply pressure for each channel is the same, slightly different values are displayed. Displays exact the same pressure values for all channels. kPa MPa Auto identification function (page 14) Can automatically identify the pressure range of a connected SMC sensor.
Insulation resistance Between external terminal and case 2M (500V DC by megameter) Vibration resistance 10 to 500Hz Width: 1.5mm or acceleration 98m/s2 (at the smaller vibration) to X, Y, Z direction (2 hours) Shock resistance 980m/s2 to X, Y, Z direction (3 times for each direction) Protective construction Panel mounting type: IP66 (Used gasket at panel mount part only), Wall mounting, DIN
Caution Refer to pages 16-14-3 to 16-14-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 16-1-11 to 16-1-13 for Precautions on every series.