SI unit Description and Functions 9 5-1 LED indication 9 5-2 Terminal board 9 5-3 Address setting 10 5-4 Setting of Hold/Clear 11 6. Wiring 12 6-1 Communication wiring 12 6-2 Terminal resistance 13 6-3 Cable for communication line 13 6-4 Wiring to power supply 13 7. Troubleshooting 14 -1No.EX-OMF0012-B 1.
How to Use . 11 2-1. Procedures to operation . 11 3. Wiring . 12 3-1. AC adapter type/ IZG10-01, 02 . 12 3-2. Power supply cable type/ IZG10-03 . 12 4. Function . 13 4-1. Name of parts . 13 4-2. LED indication . 13 4-3. Mode setting switch . 14 4-4. Emitter maintenance (cleaning and replacement) . 15 4-5. Alarm function . 17 5. Performance . 18 5-1.
If the minimum setting unit is 1 L/min, the flow can be displayed in 1 L/min units, i.e. 10, 11, 12. Minimum setting unit N Normal condition (NOR) Reference condition for volumetric flow: 101.3 kPa, 0 C The flow measurement which is converted at normal atmospheric pressure conditions at 0 C.
Exhaust Port Exhaust Residual pressure exhaust button (2.9) Port -4- Warning Warning Design/ Selection Design/ Selection (11) Push the residual pressure exhaust button all the way to the end position by using a tool. Push the residual pressure exhaust button all the way to the end position by using a tool having a tip diameter of 2.8 or below.
No.PS-OMM0005-J PRODUCT NAME Digital Pressure Switch MODEL / Series / Product Number ZSE10(F) ISE10 Table of Contents Safety Instructions 2 Model Indication and How to order 9 Summary of Product parts 11 Definition and terminology 12 Mounting and Installation 15 Installation 15 Piping 17 Wiring 18 Internal circuit and wiring example 19 Pressure Setting 20 Measurement mode 20 Function Setting
Recommended tightening torque: Modular AR/AW series 0.60.05 Nm ARM10/11 series 0.320.03 Nm Mount the main body of the Pressure switch. Insert the lock pin to the adapter to the end firmly. Supply pressure slowly, and ensure no air leaks.
No.PS-OMM0003-J PRODUCT NAME Digital Pressure Switch MODEL / Series / Product Number ZSE80(F) ISE80(H) Table of Contents Safety Instructions 2 Model Indication and How to Order 9 Summary of Product parts 10 Definition and terminology 11 Mounting and Installation 14 Installation 14 Piping 16 Wiring 17 Pressure Setting 19 Measurement mode 19 Function Setting 21 Function selection mode 21 Default
Air Cylinder Speed controller Solenoid valve Regulator Air source Air filter Fig. 11 Basic Circuit 28 6.
The use of screws that are too long can touch the body and cause malfunction. 11. Do not operate by fixing the table and moving the actuator body. 12. The belt drive actuator cannot be used for vertically mounted applications. 13. Vibration may occur during operation, this could be caused by the operating conditions.
And Adjust the offset voltage after supplying power. 23 Doc.No.IZ-OMK0015D (11) Timing chart Timing chart of normal operation Normal operation Reset operation Remarks Turn the power off to solve the problem, then supply power again. The error signal(OUT3) will be reset.
CONTENTS SAFETY 2 General General 3 positions 5 positions Model Indication Method 5 Names and Functions of Individual Parts 6 Installation 9 3 positions Names and Functions of Controller 11 Example of Internal Circuit and Wiring 12 Setting 15 Operation Characteristics 20 Specifications 21 5 positions Names and Functions of Controller 23 Example of Internal Circuit and Wiring 24 Setting 27
Order for tightening mounting screws 11 2-9-2. Auto switches When an auto switch is mounted or its set position is changed, refer to Fig. 4 to 11. C a u t i o n Use a specific mounting bracket (Page 19, Table 2) . Tighten mounting screws to the appropriate torque. The auto switch can only be used for cylinders with a built-in magnet for auto switch (e.g. CDA).
13 90 3.2 AR60K-B 70 66 65.8 11 13 90 3.2 Note 1) B dimension is a size in the state to unlock the handle.
AW20-B 11 AW20-B 0.80.1Nm AW30-B 17 AW30-B 2.350.3Nm AW40-B 21 AW40-B 3.50.3Nm Disassembly Remove the bowl assembly, housing, and element. Hexagon Remove a housing from a body by turning 4 mounting screws to the left with a hexagon wrench key. wrench key Nominal5 Remove the valve guide.
Operation and Mounting 2.1 Air Supply -P. 5 2.2 Operating Environment -P. 6 2.3 Design -P. 6 2.4 Mounting and Installation -P. 8 2.5 Piping -P. 10 2.6 Speed Control -P. 11 2.7 Shock Absorbing Mechanism -P. 11 2.8 Directional Control -P. 12 2.9 Mounting of Auto Switch -P. 13 3. Maintenance and Inspection 3.1 Inspection -P. 14 3.2 Maintenance -P. 14 3.3 Replacement Parts -P. 14 4.
Refer to Disassembly Drawing on page 11 for the part No. and the replacement procedure of the finger assembly and the body assembly. 15 - Construction/Parts list 2 MHF2-12D to 20D Components No. Description Material Note No.
Wiring 1) Insert cable gland (4), washer (5) and rubber seal (6) into cable (7) in order, and insert it into housing (2). 2) Loosen screws (11) on terminal (3). Insert lead wires (10) and tighten screws (11) again. Note 1) The tightening torque should be 0.5 Nm +/15%. Note 2) The applicable outside diameter of cable (7) is 6 to 8 mm.
Check if the dispersion is within the display accuracy range. 11 Product failure Replace the product. -52No.PS-OML0003-J Fault No. Fault Possible cause Investigation method Countermeasure Install a 5 m filter to prevent foreign matter from entering the pressure port. Also, clean the filter regularly to prevent drainage deposits.
Not adhering to these specifications, can result in damage to the product. 11 XL*-OMI0013-B 7-2.