PAB-OM-C006-B When installing piping or a fitting into a port, ensure that sealant material and cutting chips of threads do not enter piping. When using sealant tape, leave the first 2 threads exposed at the end of piping /fitting. T ightening torque Undertightening causes liquid or air leakage w hile overtightening causes breakage of threads and other parts.
When installing piping or a fitting into a port, ensure that sealant material and cutting chips of threads do not enter piping. When using sealant tape, leave the first 2 threads exposed at the end of piping/fitting. T ightening torque Undertightening causes liquid or air leakage w hile overtightening causes breakage of threads and other parts.
When installing piping or a fitting into a port, ensure that sealant material and cutting chips of threads do not enter piping. When using sealant tape, leave the first 2 threads exposed at the end of piping /fitting. T ightening torque Undertightening causes liquid or air leakage w hile overtightening causes breakage of threads and other parts.
IP65() 4.57()JIS C 3306 0.51.5mm 22 ,3 O JIS C2805 R1.25-3 Y () 1.25-3 2.53.7 0.290.35Nm () 4 4 4 4 5 5 5 5 (3 ) 0.50.6Nm 2 () 2 () 1 () 1 () 4() 3() 4() 3() 5() 4 5 DC AC DC AC SGC SGH AC 9 SGC200*-OMJ0004-A SGC/SGH Series SGC/SGH Series SGC/SGH Series SGC/SGH Series/ / / / DIN DIN DIN DIN AC DC DIN IP65() ( ( ( ( ) ) ) ) (4.5~7) IP65() NL:,R: LED:,R: V: V: 180 AC DIN (DO
Do not use Use in combination with the DI Filter Set (HRS-DP001) is not possible. to tighten the case. resin filter case (1)). After mounting the particle filter bracket, tighten the M5 screws on the back of the thermo-chiller panel.
Do not use to tighten the case.
Do not use to tighten the case. * When using the filter, the supply pressure should be 0.69 MPa (100 psi) or lower. Please replace the element when the pressure drop of this product reaches 0.15MPa. For replacement of the element, confirm the pressure inside the filter is zero, and refer to mounting procedure 3) and 4). 2.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not disassemble the product. , as this could allow contact with any residual chemicals. 1) The product does not operate when power is applied. The product creates suction, but does not dispense. There is no suction. Countermeasures Warning 2) Pump operates, but does not dispense. Operating frequency is too high. The frequency should be set at or below the maximum operating frequency.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1.The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any
We do not use soft solder joints on any of our products. Example: 1/4 BSPT to 1/8 (F) (Line # 94, Page 23) 1 5/64 Ref 2. The fittings in this catalog are shown at actual size for quick visual reference. 9 __ 16 9/16 Hex 33 __ 64 3. Product availability: Brass... Stainless... Nickel Plated All products are available in brass directly from inventory.
33 7 6 88 98 22 32 5.5 5 30 64 20 53 37 8 8 102 112 24 38 5.5 6 36 83 25 53.5 37.5 9 7 114 126 30 40 6.6 6 42 93 32 59.5 37.5 10 12 138 154 34 50 9 9 48 112 40 66 44 10 12 146 162 40 60 9 9 54 120 50 72 44 12 16 178 198 46 65 11 10 64 148 63 77 49 12 16 192 212 58 75 11 10 78 162 80 96.5 56.5 16 24 238 262 54 90 13.5 16 91.5 202 100 116 66 19 31 280 308 62 100 15.5 22 111.5 240 Caution Do