Take measures to prevent freezing when 41F (5C) or less, since moisture in circuits can freeze and cause damage to seals and lead to malfunctions. Piping Caution 1. Preparation before piping Before piping is connected, it should be thoroughly blown out with air (flushing) or washed to remove chips, cutting oil, and other debris from inside the pipe. 2.
Action Double acting Proof pressure 1.5 MPa Maximum operating pressure 1.0 MPa Minimum operating pressure 0.08 MPa 0.2 MPa Piston speed 50 to 500 mm/sec* 15 to 300 mm/sec* Ambient and fluid temperature Without auto switch: 10C to 70C With auto switch: 10C to 60C (No freezing) 5C to 60C Cushion Air cushion None Stroke length tolerance Up to 250: +1.0 0 , 251 to 1000: +1.4 0 , 1001 to 1500:
./0.05 MPa Ambient and uid temperature 5C to 60C Port size Rc1/4 (Gauge port Rc1/8) Weight Approx. 700 g (at 100 mm stroke) Construction/Principle of Operation When signal pressure enters input chamber q, the input diaphragm e is deected left. Clearance of the nozzle y is reduced causing higher back pressure at diaphragm A u.
Clean Exhaust Filter SFE Series RoHS How to Order SFE 11 Size/Port size Male thread type Plug-in type Symbol Port size Max. ow capacity L/min (ANR) 11 M5 x 0.8 3 42 R1/8 65 52 R1/8 130 53 R1/4 130 73 R1/4 200 Symbol Port size Max. ow capacity L/min (ANR) 3A 4 30 4B 6 65 5C 8 130 7D 10 200 Male thread type One-touch tting type Symbol Applicable tubing O.D.
Take measures to prevent freezing at temperature below 5C, since moisture in circuits may freeze and cause damage to seals and lead to malfunctions. 5. Instruction manual Install the products and operate them only after reading the instruction manual carefully and understanding its contents. Also keep the manual where it can be referred to as necessary. Cushion Caution 1.
In addition, the cooling water cannot theoretically be cooled to a temperature any lower than 5C above the wet-bulb temperature of the outside air.
(However, auto switch mounting brackets are assembled when being shipped.) 396 Series CA2WH Air-hydro Cylinder: Air-hydro Type Double Acting, Double Rod Specifications Bore size (mm) 100 80 63 50 40 Type Air-hydro Fluid Turbine oil Action Double acting Proof pressure 1.5 MPa CJ1 Maximum operating pressure 1.0 MPa Minimum operating pressure 0.16 Mpa CJP Piston speed 0.5 to 300 mm/s 5C to 60C
Take measures to prevent freezing when below 5C, since moisture in circuits can freeze and cause damage to seals and lead to malfunctions. For compressed air quality, refer to Air Preparation Equipment catalog. Winding direction Pipe tape Expose approx. 2 threads 95 Actuator Precautions 3 Be sure to read before handling. For detailed precautions on every series, refer to main text.
Use in low temperature environments The valve can be used at a temperature down to 5C. Take appropriate measures to avoid freezing of drainage, moisture, etc. 2. Operation method The valve must be switched to each position instantly and securely. Stopping the handle halfway between the extreme positions may cause malfunction. VHS 5-8-15
Buffer stroke 25 50 75 100 40 50 63 80 100 125 Series ZPT ZPX Pad Material and Characteristics : Little or no influence : Can be used depending on conditions X: Not suitable Characteristics Operating temperature range (C) Oil resistance gasoline Oil resistance benzol Solvent resistance (Benzene, toluene) Durometer HS (5C) Base resistance Acid resistance Abrasion resistance Ozone resistance
Take measures to prevent freezing, since moisture in circuits will be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMC's Best Pneumatics catalog vol. 4 for further details on compressed air quality. 4. Take measures to prevent possible fluctuations in pressure.
Take measures to prevent freezing at temperature below 5C, since moisture in circuits may freeze and cause damage to seals and lead to malfunctions. 5. Instruction manual Install the products and operate them only after reading the instruction manual carefully and understanding its contents. Also keep the manual where it can be referred to as necessary. Cushion Caution 1.
Note 4) Facility water flow rate that satisfies the conditions in which the facility water inlet temperature is 32oC and the outlet temperature is 37oC ( t = 5C) when the rated load is applied.
Take measures to prevent freezing, since moisture in circuits can be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. Piping Caution 1.
Take measures to prevent freezing, since moisture in circuits can be frozen below 5C, and this may cause damage to seals and lead to malfunction. Refer to SMC Best Pneumatics 2004 Vol. 14 catalog for further details on compressed air quality. Wrapping direction Expose approx. 2 threads Pipe tape Lubrication Operating Environment Caution Warning 1. Lubrication on cylinder.
Take measures to prevent freezing, since moisture in circuits can be frozen under 5C, and this may cause damage to seals and lead to malfunction. Refer to SMCs Air Cleaning Equipment catalog for further details on compressed air quality. Maintenance Warning 1. Removal of equipment, and supply/exhaust of compressed air.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals and equipment malfunction. Therefore, take appropriate measures to prevent freezing. For compressed air quality, refer to Best Pneumatics No. 5. Cushion Caution 1. Readjust using the cushion needle.
Take measures to prevent freezing, since moisture in circuits can be frozen below 5C, and this may cause damage to seals and lead to malfunction. Refer to Best Pneumatics 2004 Vol.14 catalog for further details on compressed air quality. Wrapping direction Maintenance Expose approx. 2 threads Warning Pipe tape 1. Removal of equipment, and supply/exhaust of compressed air.
VP7 3 5 Plug-in: SS5Y -Type 45 VQC Q 5 SY 5 1 FU Single solenoid: 5 SQ Q 5C FU Double solenoid: 5 SY 5 1 VQ VQ4 Series Manual override 3 SY300 5 SY500 Nil Non-locking push type VQ5 D Push-turn locking slotted type E Push-turn locking lever type VQZ Type of actuator 1 Normally closed (N.C.) Rated voltage VQD 2 Normally open (N.O.)
Size/Port: 5C [Plug-in Type, Port Size: ø8, Flow: 130 L/min (ANR)]