Rotary Table If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals and equipment malfunction. Therefore, take appropriate measures to prevent freezing. 9 - Operating Environment 1. Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, steam, or Warning where there is direct contact with any of these.
Take measures to prevent moisture from freezing in a piping circuit when using at 5C or less, since this may cause damage to the product and lead to malfunction.
1.41 0.41 1.07 0.46 1.32 0.52 1.33 0.51 1.71 0.28 0.82 0.34 1.07 0.23 0.81 0.19 0.49 335 LLB Series Specifications Model LLB3 LLB4 Clean Air Module Common Specifications Fluid Clean air, N2 gas (Inlet air conditions: equivalent to ISO 8573-1 and Quality Class 1.4.1-1.6.1) Note 3) Maximum operating pressure 0.7 MPa Set pressure 0.05 to 0.4 MPa Withstand pressure 1.0 MPa Fluid temperature 5C
. *4 The facility water flow rate that satisfies the rated conditions with a facility water inlet temperature of 32C and an output temperature of 37C ( t = 5C) *5 These values are obtained under rated conditions with a rated facility water flow rate and a facility water inlet pressure of 0.2 MPa. *6 These values are obtained under rated conditions (1 RT = 4.535 kW). *7 These values are reference
./0.05 MPa Ambient and fluid temperature 5C to 60C Port size Rc1/4 (Gauge port Rc1/8) Weight Approx. 700 g (at 100 mm stroke) Construction/Principle of Operation When signal pressure enters input chamber q, the input diaphragm e is deflected left. Clearance of the nozzle y is reduced causing higher back pressure at diaphragm A u.
Specifications Cleanliness class (ISO class) Class 3 Note 1) KPQ Series Brass (electroless nickel plated) Release button: Light gray Fluid Air Maximum operating pressure (20C) 1 MPa Note 2) Operating vacuum pressure 100 kPa Proof pressure (20C) 3 MPa 5C to 60C Ambient and fluid temperature Threads JIS B0203 (Taper thread for piping) Oil Fluorine-based grease Note 1) Refer to particle generation
If water is used for the circulating fluid, set its temperature to over or more 41F (5C) to prevent it from being frozen. 6. Clear Water (as Circulating Water) Quality Standards 1. The catalog shows the specifications of the Thermoelectric Bath. 1.
Cooled substance total volume V Cooling time h Cooling temperature difference T Circulating fluid : 20 L : 15 min : 5C (5 K) : Clear water Density : 1 x 103 kg/m3 Specific heat C: 4.2 x 103 J/(kgK) T xV x x C h x 60 x 1000 Q = Cools 20 L of clear water from 30C to 25C in 15 minutes. 5 x 20 x 1 x 10 3 x 4.2 x 10 3 V = 15 x 60 x 1000 AL SI OUT = 467W PURGE OUT PURGE IN CHEMICAL POWER IN WATER
Water Physical property value Temperature Density [kg/L] Specific heat C [J/(kgK)] Conventional units Weight volume ratio [kgf/L] Specific heat C [cal/(kgfC)] 5C 1.00 4.2 x 103 1.00 1 x 103 10C 1.00 4.19 x 103 1.00 1 x 103 15C 1.00 4.19 x 103 1.00 1 x 103 20C 1.00 4.18 x 103 1.00 1 x 103 25C 1.00 4.18 x 103 1.00 1 x 103 30C 1.00 4.18 x 103 1.00 1 x 103 35C 0.99 4.18 x 103 0.99 1 x 103 40C
Take measures to prevent freezing at temperature below 5C, since moisture in circuits may freeze and cause damage to seals and lead to malfunctions. 5. Instruction manual Install the products and operate them only after reading the instruction manual carefully and understanding its contents. Also keep the manual where it can be referred to as necessary. Cushion Caution 1.
Action Double acting Proof pressure 1.5 MPa Maximum operating pressure 1.0 MPa Minimum operating pressure 0.08 MPa 0.2 MPa Piston speed 50 to 500 mm/sec* 15 to 300 mm/sec* Ambient and fluid temperature Without auto switch: 10C to 70C With auto switch: 10C to 60C (No freezing) 5C to 60C Cushion Air cushion None Stroke length tolerance Up to 250: +1.0 0 , 251 to 1000: +1.4 0 , 1001 to 1500:
Take measures to prevent freezing at temperature below 5C, since moisture in circuits may freeze and cause damage to seals and lead to malfunctions. 5. Instruction manual Install the products and operate them only after reading the instruction manual carefully and understanding its contents. Also keep the manual where it can be referred to as necessary. Cushion Caution 1.
Take measures to prevent freezing at temperature below 5C, since moisture in circuits may freeze and cause damage to seals and lead to malfunctions. 5. Instruction manual Install the products and operate them only after reading the instruction manual carefully and understanding its contents. Also keep the manual where it can be referred to as necessary. Cushion Caution 1.
Take measures to prevent freezing at temperature below 5C, since moisture in circuits may freeze and cause damage to seals and lead to malfunctions. 5. Instruction manual Install the products and operate them only after reading the instruction manual carefully and understanding its contents. Also keep the manual where it can be referred to as necessary. Cushion Caution 1.
Take measures to prevent freezing at temperature below 5C, since moisture in circuits may freeze and cause damage to seals and lead to malfunctions. 5. Instruction manual Install the products and operate them only after reading the instruction manual carefully and understanding its contents. Also keep the manual where it can be referred to as necessary. Cushion Caution 1.
Take measures to prevent freezing at temperature below 5C, since moisture in circuits may freeze and cause damage to seals and lead to malfunctions. 5. Instruction manual Install the products and operate them only after reading the instruction manual carefully and understanding its contents. Also keep the manual where it can be referred to as necessary. Cushion Caution 1.
Mandrel = LD 2d 1 x 100 Here, : Deformation ratio (%) d: Tube diameter (mm) L: Measured length (mm) D: Mandrel diameter (mm) (Twice against the minimum bending radius) Test temperature: 20 5C Relative humidity: 65 5% Air Supply Warning 5.Do not use fluids other than specified. The only fluid that can be used is air. 1. Use clean air.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals and equipment malfunction. Therefore, take appropriate measures to prevent freezing. For compressed air quality, refer to the Product Selection Guide. 5.
If the fluid temperature is 5C or less, the moisture in the circuit could freeze, causing damage to the seals and equipment malfunction. Therefore, take appropriate measures to prevent freezing. For compressed air quality, refer to the Product Selection Guide. 5.
Buffer stroke 40 50 63 80 100 125 Series ZPT ZPX Related 25 50 75 100 Equipment Pad Material and Characteristics Characteristics Operating temperature range (C) Oil resistance gasoline Oil resistance benzol Base resistance Acid resistance Weatherability Ozone resistance Abrasion resistance Waterproof Solvent resistance (Benzene, toluene) Durometer HS (5C) Material 50C 50C 50C 60C 60C NBR