Vacuum Ejector with Solid State Timer, Series ZMA Do not allow repeated bending or stretching forces to be applied to lead wires. Wiring arrangements in which repeated bending stress or stretching force is applied to the lead wires can cause broken wires. 1. Do not drop or bump. Do not drop, bump or apply excessive impact (1,000m/s) when handling.
Installation location Do not install this product in an area that is exposed to water or direct sunlight. Do not install in locations influenced by vibrations. If it must be used in such an area due to unavoidable circumstances, please contact SMC beforehand. 14-9-4 5 Booster Regulator Series VBA1110 to 4200 4.
For air
Do not allow repeated bending or stretching forces to be applied to lead wires. Wiring arrangements in which repeated bending stress or stretching force is applied to the lead wires can cause broken wires. 1. Do not drop or bump. Do not drop, bump or apply excessive impact (1,000m/s) when handling.
Do not hold the release button to avoid damage. VS DIN Rail Removal/Mounting To remove manifold from DIN rail: 1) Loosen the clamp screw on the "A" side of both ends of the manifold. 2) Lift the "A" side of the manifold off the DIN rail and slide it in the direction of the "B" side.
Do not drop or bump. Do not drop, bump or apply excessive impact (1,000 m/s2) when handling. Even if the switch body is not damaged, the switch may suffer internal damage that will lead to malfunction. 2. Hold the product from the body side when handling. The tensile strength of the power cord is 49 N, and pulling it with a greater force can cause failure. 3.
Vcior on up to 4 S des Ava able (lvlagnet Type) s NCQT very Cornpact sides and do Black Line s NCOB Outer Rcd C rcll] is B;mba Flat lrt Fla'.1r, s re!'
NVV5Z5-4 2-( 05 ) 1 -r87T) Y -r.Stationsa asize ot A, B port E-?
(Do not tighten with pliers.) RB J D How to change position of electrical entry After separating the terminal block from the terminal cover, change the position of the terminal cover to any desired direction (4 directions at every 90) to change the position of electrical entry.
Do not use a pair of pliers, nippers, or scissors because they could result in an uneven cut or cause the tube to become flattened. As a result, it might not be possible to connect the tubing, or after the tube has been connected, it could pull out or allow air to leak.
NVV5Z5-4 2-( 05 ) 1 -r87T) Y -r.Stationsa asize ot A, B port E-?
W With locking at head side With locking at rod side q Do not use a 3 position solenoid valve. Avoid using circuit with 3 position solenoid valve (especially closed center). When pressure is trapped in the port with locking mechanism, end lock is free.
Do not plug or tighten it. (P port) (A port) (R port) 5-5-11 2 Series VGA342 Made to Order Specifications: Please contact SMC for detailed specifications, dimensions and delivery.
Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). Also, since there is a breathing port for the armature in the manual override part, do not allow accumulation of dust and/or other foreign materials to block bleed port.
You do not need to specify "N" (i.e., without lead wire) for D-A3, D-A44, D-G39, and D-K39.
(Mp,My values do not apply to this example.) Mr=W (L3 + C) = 10 (.05 + 0.014) =0.64 [N m] W Mr 2 =Mr/Mr max. =0.64/12 =0.053 Mr: Mr max. value is from
Series: 2 (VQ20), Stations: 5 Stations
Series: VQ20, Stations: 5 Stations, Option: -, Thread: -
Series: 2 (VQ20), Stations: 8 Stations, Option: DO (DIN Rail Mount w/o DIN Rail), Thread: 00N (NPT3/8)
Series: 2 (VQ20), Stations: 10 Stations, Option: DO (DIN Rail Mount w/o DIN Rail), Thread: 00N (NPT3/8)