JIS Standard Hydraulic Cylinder Some trunnion mounting positions do not allow auto switch mounting. Please consult with SMC for more information.
Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
Do not hold the release bushing to avoid damage. DIN Terminal Part No. Without light AXT100-20-1 With Indicator Light DIN Rail Removal/Mounting Rated voltage 24 VDC 12 VDC 100 VAC 200 VAC 110 VAC 220 VAC Voltage symbol 24V 12V 100V 200V 110V 220V Part no. AXT100-20-2-05 AXT100-20-2-06 AXT100-20-2-01 AXT100-20-2-02 AXT100-20-2-03 AXT100-20-2-04 Circuit with indicator light Removing 1.
Specifications Specifications Standard specifications Symbol 02 05 For connection of PCW unit compatible with KEYENCE CORP.
Do not use in a location having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. Do not use in locations where radiated heat will be received from nearby heat sources. Maintenance Maintenance Warning 1. Maintenance should be performed in accordance with the procedures in the instruction manual.
With cushion on head end 05 Exension cable CE1-R Cable length 05 10 15 20 Suffix 5 m Nil Extension cable 10 m C Extension cable & connector 15 m 20 m Applicable Auto Switches/Refer to pages 941 to 1067 for further information on auto switches.
YES YES Do you want better communication and control capabilities for your system?
NO Do you have any problem, even if it might run over the target position? (Overrun) YES NO During the positioning operation, there may be the case it needs to do overruns or trials again. If there is any problem during the correcting motion, the products cannot be used.
NO YES Do you have any problem, even if it might run over the target position? (Overrun) NO Do you have any problem, although an error might occur if it is set to be (number of trial again = 0) in order to prevent from doing a trial again when positioning is done at the outside of the range? During the positioning operation, there may be the case it needs to do overruns or trials again.
NO YES Do you have any problem, even if it might run over the target position? (Overrun) NO Do you have any problem, although an error might occur if it is set to be (number of trial again = 0) in order to prevent from doing a trial again when positioning is done at the outside of the range? During the positioning operation, there may be the case it needs to do overruns or trials again.
Note 2) Do not use it in a line that is kept pressurized because it could cause the body to break.
Size NT-03 NT-MU03 NT-04 NT-05 25 32 40 50, 63 M10 x 1.25 M12 x 1.25 M14 x 1.5 M18 x 1.5 6 7 8 11 17 19 22 27 19.6 21.9 25.4 31.2 16.5 18 21 26 S + Stroke H + Stroke A nut is attached to the rod end male thread as standard.
MGG (Max.)W1 B DX Z + Stroke MGC DDH10 hole 90 B MGF 4-DT B DS A DH DF CY1 DO DO DC DE DU DU DL DA 4-DR MY1 Rotation angle (mm) Bore (mm) 40 50 63 80 100 Bore (mm) 40 50 63 A B A + B + 90 Part No.
*Do not wipe with alcohol, etc. It may cause damage to the parts. 1 B
DO Without air cushion (mm) Bore size (mm) Part No.
Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). The grommet portion contains a breather hole for the core.
Do not disassemble the product. Once the product is disassembled and reassembled, it will not be able to satisfy the original performance. 4. When piping, do not get the pad side and vacuum generator side of the product the wrong way round. (Refer to Fig. 1.)
Lubrication The bearing can be used in an oilless state, but when you are going to oil the bearings, do so by using a nipple so that no foreign matter will be mixed. For the grease, we recommended using high-quality lithium soapbased grease no. 2. 6.
Therefore, do not adjust the stroke with the adjustment bolts or shock absorbers. 8. Do not use an air cylinder as an air-hydro cylinder. This will cause leakage of hydraulic fluid. 9. Adjust an auto switch's position so that it operates for movement to both the stroke end and backlash (2 mm) positions.
Dimensions q Do not use the air cylinder as an air-hydro cylinder. This will cause an oil leak. w Install without twisting the bellows. If the cylinder is installed with its bellows twisted, it could damage the bellows. Rubber bumper Disassembly/Replacement Caution q Do not replace the bushings or the cushion seals. The bushings and the cushion seals are press-fit.