Table of Contents - Tubing Do not use in locations where static electric charges will be a problem. Please consult with SMC regarding use in this kind of environment. 2. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire. 3. Do not use in environments where there is direct contact with liquids such as cutting oil, lubricating oil or coolant oil, etc.
Do not disassemble the product. Once the product is disassembled and reassembled, it will not be able to satisfy the original performance. 4. When piping, do not get the pad side and vacuum generator side of the product the wrong way round. (Refer to Fig. 1.)
CJ1 q Do not apply more than the allowable rotating torque to the piston rod. If more than the allowable rotating torque is applied, the non-rotating guide will be deformed and there will be a significant loss of rotational accuracy. This may cause damage to the machinery.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. A protective cover, etc. should be used to shield valves from direct sunlight. 5.
The load ratio is obtained by the following formula: ((Load mass x 9.8)/Theoretical output) x 100% Conditions MB, CA2 series CS1, CS2 series Series Condition 10A x 1 m SGP (Steel pipe) dia. x Length VQ4100--03 VQ4101--03 AS420-03 Speed controller AN30-03 Silencer 10A x 1 m SGP (Steel pipe) dia. x Length VQ5100--04 VQ5101--04 AS420-04 Speed controller AN40-04 Silencer 448 INDEX Page 446 Base
1/2 72 62 40 62 Y52-03 3/8 14 24 41 Y61-03 3/8 15 30 50.5 Y61-04 1/2 15 30 50.5 Courtesy of Steven Engineering, Inc. !
-01 KDM20S-03 KDM20S-07 KDM20P-01 20 KDM20P-03 KDM20P-07 KDM20S-09 KDM20P-09 Clamp bolt Panel mounting Loosen (4) screws for bracket on the socket side using a Phillips screwdriver (JIS nominal No. 2) until the bracket touches the stop ring.
Do not use these for pneumatic operations because they will lead to oil leaks. Air-hydro cylinder: CA1HCQ2HCS1HCM2HCG1H(up to 63) HC03-X1x Air-hydro rotary actuator: CRA1H2.
Do not use these for pneumatic operations because they will lead to oil leaks. Air-hydro cylinder: CA1HCQ2HCS1HCM2HCG1H(up to 63) HC03-X1x Air-hydro rotary actuator: CRA1H2.
Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: 03-5207-8249 Fax: 03-5298-5362 https://www.smcworld.com 2022 SMC Corporation All Rights Reserved Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. D-G
Conditions: Operating pressure 0.5MPa, Operating oil Turbine oil Class 1 (ISO VG32), Piping length 1m AS420-02, 03, 04 AS500-06 AS2000-01, 02 AS600-10 AS3000-02, 03 AS4000-02, 03, 04 Circuit 4.12-12
Do not use in lines where a pressurized condition is maintained, as the body may be damaged. Warning Caution 1. Tubing attachment/detachment for One-touch fittings 1) Installing the tubing (1) Use tubing with no flaws on its periphery and cut it off at a right angle. When cutting the tubing, use a tube cutter, TK-1, 2 or 3. Do not use pinchers, nippers or scissors, etc.
SX7120-02 SV AS200-02 AN110-01 SZ Conditions [When using SGP (Steel pipe)] Base mounted Series MB Series CS1 SGP10A x 1 m AS420-03 AN300-03 SY SX7140-03 Tube x Length Speed controller Silencer SYJ SX Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 1-6-3 4 Courtesy
Do not grip the piping port on the back side or the handles of the panel. 3. Do not pass over bumps, etc., with the casters.
Do not use valves where there is direct contact with, or in atmospheres of, corrosive gases, chemicals, salt water, water or steam. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. Confirm the specifications for each series. 4. A protective cover should be used to shield valves from direct sunlight. 5.
(Example) SS3YJ5-20-03 . 1 set (manifold base) SYJ512-5LZ-M5 . 2 sets (valve) SYJ500-10-1A . 1 set (blanking plate assembly) SS3YJ5-41R-03-C6 . 1 set (manifold base) SYJ514R-5G . 2 sets (valve) SYJ500-10-3A . 1 set (blanking plate assembly) The asterisk denotes the symbol for assembly.
(Example) SS3YJ7-20-03 . 1 set (manifold base) SYJ712-5LZ-01 . 2 sets (valve) SYJ700-10-1A . 1 set (blanking plate assembly) SS3YJ7-42R-03-01 . 1 set (manifold base) SYJ714R-5G . 2 sets (valve) SYJ700-10-2A . 1 set (blanking plate assembly) The asterisk denotes the symbol for assembly.
Tie-rod nut *Actuators do not use metal containing copper.
Note 2) This filter does not include any companion flange, companion flange bolt, and O-ring. 4 x K depth L DRAIN (): Internal dimensions for FH342 type (mm) Model Weight (kg) d A B C D E F G H J J' K L M N P Q Threaded Rc Flange SSA FH340-03 FH340-04 FH342-06 FH342-08 FH34 -10 FH34 -12 FH341-16 FH440-03 FH44 -04 FH44 -06 FH44 -08 FH44 -10 FH44 -12 FH441-16 FH441-20 FH441-24 FH540-03 FH54
Load factor: ((Load weight x 9.8)/Theoretical force) x 100% VS4 VQ7 EVS Conditions VFN Base mounted Series MB Series CS1 6A x 1 m AS4000-02 AN200-02 10A x 1 m AS420-03 AN300-03 6A x 1 m AS4000-02 AN200-02 10A x 1 m AS420-03 AN300-03 Base mounted Series MB Series CS1 10A x 1 m AS4000-03 AN300-03 15A x 1 m AS420-04 AN400-04 10A x 1 m AS4000-03 AN300-03 15A x 1 m AS420-04 AN400-04 SGP (Steel