<br><br>For plug lead type manifolds:<br>The max. number of stations that can be increased depends on the wiring kit.
<br>“VVFS2000-22A-1” is the plug-in type perfect spacer part number for the VFS2600.<br>And “VVFS2000-22A-2” is the non plug-in type perfect spacer part number for the VFS2610.<br>The “□” in the VVFS□000-22A-1 and VVFS□000-22A-2 part numbers is to indicate the series (VFS2000/3000/4000/5000 series).<br><br>
<br>Note) A cylinder with a lock may be required depending on the operating conditions.
<br><br>Non plug-in type:<br>Electrical connection is made on the solenoid valve side. Electrical connection is required when replacing the solenoid valve.
<br>Reference) The manifold specification (a VOA301 valve and a VVTA300 base) of the air operated VTA301 series valve can also be changed to from N.C to N.O. by turning over the switching plate in the same way.<br><br>
<br>VS4120, VS4130, and VS3135 series valves with a grommet have 2 lead wires.<br>Connections: For 100 VAC, there are 2 blue wires. For 200 VAC, there are 2 red wires. And for 24 VDC, there is 1 white wire and 1 pink wire.<br>VS4140 and VS3145 series valves have 3 lead wires for AC voltage types and 2 lead wires for DC voltage types.
<br>(They are matched to the individual component dimensions.)<br>Coils of VT317 (VO317) series valves, however, can be ordered, excluding CE-compliant products with the part number suffix “-Q.” Refer to the catalog for the coil assembly part numbers.<br>Do not use coils for DC in valves whose rated voltage is AC, and vice versa.
<br><br>
<br><br>For further details, refer to the catalog of each series.
<br>1) When the product is operated with air supplied to only one side, such as during a test operation<br>2) When the air in the cylinder is exhausted and back pressure cannot be secured during operation<br>3) When a meter-in speed controller is installed and the rise of the supply-side pressure during operation is suppressed<br>4) When the load factor exceeds 50% for vertical downward operation
<br>2) If internal leakage of the valve or leakage of the piston seal occurs, air may collect around the lock mechanism, and the lock may be released.<br>For the pressure center type<br>1) When air is supplied to both sides at the center position, the lock is released.
<br><br>For end lock cylinders:<br>Locking can only be performed at the stroke end of the cylinder on the side with the lock mechanism. As they have almost the same dimensions as the standard cylinder, they can only be operated with a standard 5-port 2-position valve.
<br><br><br>Round bar type: This is the general type.<br>Chamfered type: The pallet contact surface of this type has been flattened (chamfered on one side), and the contact surface is fixed.<br>Roller type: This is a chamfered type with a resin roller at the end.
<br>③ For new MY1, MY2, and MY3 series cylinders, only the new seal belt needs to be ordered.<br>④ The min. operating pressure of new bore size ø16 and ø20 cylinders has been changed as well (0.15 MPa for the MY1B, MY1C, MY1H, and MY series and 0.2 MPa for the MY1M and MY3 series).
<br>Order using the following rod boot assembly part numbers.<br>Ex.) The rod boot part number for the MBL63-400JZ is “C2A50GAEA034-R-400.”<br>Note) A band for the rod boot is included.<br>For MB Cylinders J rod boot assembly part no.
<br>
<br>Refer to the excerpt about the double knuckle joint from the “Dimensions of Accessories” page below. <br>A knuckle pin and retaining rings are included. <br>The CG1 series catalog can be found here.<br><br>
<br>Contact your nearest SMC sales representative for details. <br>The sensor part in particular needs to be protected by a cover, etc., if the product may be exposed to liquids in the operating environment.
<br>The corresponding mass is also called the corresponding mass of the impacting object. <br>① (Unit of collision speed v: m/s) Me becomes larger when the speed becomes less than 1 m/s because the square of the speed is the denominator.