Electric Actuator Power supply cable (LEC-CK1-1) is an accessory.
Cautions for use in an interlock circuit When an auto switch is used for an interlock signal requiring high reliability, devise a double interlock system to avoid trouble by providing a mechanical protection function, or by also using another switch (sensor) together with the auto switch. Also perform periodic maintenance inspections and confirm proper operation. 9.
Contact SMC if an inverter welder or a DC welder will be used.
(An assembly is shipped under the condition shown in the figure.)
Environment at an altitude of 1000 meters or higher Heat radiation and withstand voltage will decrease. Contact SMC for details. (2) Do not use in an environment where the product is directly exposed to liquid, such as cutting oils.
An auto switch magnet is not installed. In cases where an auto switch magnet is installed, add -M9// to the part number. (Not available for the high-temperature type) An auto switch is not attached. When a product with an auto switch is required, add the symbol for the auto switch to the part number.
It is necessary to use a solenoid valve with an electrical response time of 30 ms.
The drawing shows with an auto switch. Eliminate the unnecessary parts.
In the graph, find where the lines representing a load mass of 40 kg and an eccentric distance of 80 mm intersect.
but cannot be mounted in this way on (N)AW units when the handle of an (N)AR Series Regulator faces upwards.
It is necessary to use a solenoid valve with an electrical response time of 30 ms.
Never use in an atmosphere of explosive gases. 6. Do not use in an environment where there is excessive impact shock. The construction of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated.
Never use in an atmosphere of explosive gases. 6. Do not use in an environment where there is excessive impact shock. The construction of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated.
Never use in an atmosphere of explosive gases. The construction of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated. Auto switches can malfunction or magnets inside cylinders can become demagnetized.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. Back page 1 Safety Instructions Caution 1.
Note) With an operating pressure of 0.6 MPa or larger, the use of a cushion or an external shock absorber conforming to the conditions on pages 10 and 11 is recommended.
For further details, refer to mounting positions under Replacement heaters/Part Nos. on page 46.
Do not use an air cylinder as an air-hydro cylinder. This will cause leakage of hydraulic fluid. 9. Adjust an auto switch's position so that it operates for movement to both the stroke end and backlash (2 mm) positions. When a 2-color indication switch is adjusted for green indication at the stroke end, it may change to red for the backlash return, but this is not abnormal.
Power supply cable (LEC-CK1-1) is an accessory.
NX NZ Material: Rolled steel C85 Applicable bore size (mm) 125 140 160 180 200 250 300 Y-12 +0.084 0 +0.3 +0.1 0.1 0.3 32 25 64 Part no. 8 46 100 M30 x 1.5 27 42 D C B d H Y-14 125, 140 160 180 200 250 300 NT-12 NT-16 NT-18 NT-20 NT-25 NT-30 0.1 0.3 +0.084 0 +0.3 +0.1 36 28 72 8 48 105 M30 x 1.5 30 47 53.1 44 46 18 M30 x 1.5 C95 Y-16 +0.1 0 +0.3 +0.1 0.1 0.3 40 32 80 8 55 110 M36 x 1.5 34