HEC_W-E Sensuous phenomenon nothing to do with function.
Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3. Do not use in a place subject to heavy vibration and/or shock. 1. Drain flushing Remove drainage from the air filters regularly. 2. Lubrication Once lubrication has been started, it must be continued.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. Do not use the components other than the specified components. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
If they do not match, stress could be applied to the rod and the cylinder tube, causing wear to the inner surface of the cylinder tube, the bushing, the rod surface, and the seals may become damaged. 3) When mounting the cylinder, do not apply a lateral load to the rod.
Do not allow pallets to strike the lever when it is standing up. Do not allow pallets to strike the lever when it is standing up (after the shock absorber has absorbed energy), because the cylinder body will be subjected to the full energy of the impact. 2. Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc.
Do not increase the operating speed after setting the operating conditions.
Do not deform the mounting surface by mounting with workpieces tucked in. 11. Do not drive the main body with the table fixed. 12. When mounting the product, for R/L type fixed cable, keep the following dimension or more for bends in the cable. For D type, keep a 40 mm or longer diameter for bends in the cable. 2.
DC DO DL DU DU DE Rotating Angle DA Ao Bore size (mm) Ao Bo Ao + Bo + 90o 40 to 100 12o 60o 162o (mm) DDH10 (Hole) Bore size DA DL DU DC DX DE DO DR DT DS DH DF B Z Part no.
Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 2. When problems are caused by a water hammer, install water hammer relief equipment (accumulator etc.), or use an SMC water hammer relief valve (Series VXR). Please consult with SMC for details. 5.
Do not use it in such a way that excessive external force or impact force could work on it. This could result in damage. Caution 1. Do not scratch or dent the mounting side of the body, table or end plate. The damage will result in a decrease in parallelism, vibration of the guide or an increase in moving part resistance. 2.
Precautions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Safety Instructions Warning Do not disassemble, modify (including the replacement of the circuit board) or repair the product. Do not use the components other than the specified components. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. 1. Confirm model no., size, etc. before installing. Check tubing for damage, gouges, cracks, etc. The fluoropolymer tubing do not have the model number displayed on the product due to the resin material used.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water vapor, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
Do not allow pallets to strike the lever when it is standing up. Do not allow pallets to strike the lever when it is standing up (after the shock absorber has absorbed energy), because the cylinder body will be subjected to the full energy of the impact. 2. Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc.
Rotation should be controlled by connecting it to another shaft (linear guide, etc.). 3.Do not operate with the magnetic coupling out of position.
Sensor shall be inspected by experienced person with adequate knowledge. (2) Do not overhaul nor modify to avoid electric shock, failure, fire, etc. Overhauled or modified product does not guarantee spec. function or performances. Warning Handling ! (1) Do not drop, hit nor apply excess impact(100m/s2 or more).
Do not use in an environment where corrosive gases, chemicals, sea water, water or steam are present. 2. If using in a location directly exposed to sunlight, shade the product from the sunlight. 3. Do not mount the product in locations where it is exposed to radiant heat. 9 4. Do not use the product in a place where static electricity is a problem.
However, do not use the product under water.