Series PF2W Digital Flow Switch For Water Do not wire in conjunction with power lines or high voltage lines. Wire separately from power lines and high voltage lines, and avoiding wiring in the same conduit with these lines. Control circuits including switches may malfunction due to noise from these lines. 5. Do not allow a load to short circuit.
Do not use the materials for buffer face which might cause to spark by collision. Load Warning Allowable eccentric angle 1 < 5 1.
The graphs do not show the loadable mass. Refer to the Model Selection for the loadable mass.
As the connected actuator will start confirm that it is safe to do beforehand.
Do not use the materials for buffer face which might cause to spark by collision. Load Warning Allowable eccentric angle 1 < 5 1.
Open/ Close success: default output DO[101] Open / Close failure: default output DO[102] workpiece drop detection: default output DO[103] * Digital output port can be selected within DO[101] to DO[112] * you select the same digital output port for different status signals, a warning message will be displayed. 2. Test run The manual operation of the air gripper unit can be checked.
Do not use in atmospheres contacting corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not expose to direct sunlight for an extended period of time. Protective cover should be used to shield. 5.
Do not use the product in an environment where corrosive gases or fluids can be splashed. Otherwise damage to the SI can result, causing malfunction. Do not use the product in an area where surges are generated.
Do not use until you verify that the equipment can operate properly. After mounting, repair or modification, etc., connect the air supply and electric power, and then confirm proper mounting by means of appropriate function and leak inspections. Do not let chips or extraneous material enter inside the cylinder from the inlet.
DC DE DO 4 x DR DU DL DA DU With Rubber Bumper [mm] [mm] Bore size Z Part no.
Piston rod Do not turn the screws at the bottom. Do not damage the sliding surface of the piston rod of the shock absorber. Otherwise, impaired durability and return failure can result. Damage is not allowed. Shock absorber is a consumable. Replace the shock absorber when the energy absorption performance is reduced.
not have explosion-proof construction; do not use flammable gases or liquids.
Do not use in the environment, where the product could be exposed directly to the foreign matters such as powder dust, blown dust, cutting chip, spatter etc. This could result in looseness and increased operating resistance, and air leakage, etc. Please consult with SMC regarding use in this kind of environment. 3. Do not use in direct sunlight. 4.
Do not rotate the screw set on bottom of shock absorber. This is not an adjusting screw. Turning it could cause oil leakage. 2. Do not scratch the exposed portion of the piston rod. Durability could be degraded and lead to return defect.
Comfirm that the auto drain operates in the case of type with auto drain. 2.Confirm that air leakage do not occur.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 3.
Do not use the product in an environment that is exposed to temperature cycle. Do not expose the product to direct sunlight. Keep the specified ambient temperature range. Do not expose the product to heat radiation from a heat source located nearby. Set the switches by using a sharp-pointed screwdriver etc.
Do not use the product in an environment that is exposed to temperature cycle. Do not expose the product to direct sunlight. Keep the specified ambient temperature range. Do not expose the product to heat radiation from a heat source located nearby. Set the switches by using a sharp-pointed screwdriver etc.
Do not use the product in an environment that is exposed to temperature cycle. Do not expose the product to direct sunlight. Keep the specified ambient temperature range. Do not expose the product to heat radiation from a heat source located nearby. Set the switches by using a sharp-pointed screwdriver etc.
Use clean ai Do not use compressed air that contains chemicals, synthetic oils that include organic solvents, salt, corrosive gases, etc., as it can cause damage or malfunction. Do not use in an environment where flammable gas or explosive gas exists. Usage may cause a fire or explosion. The products do not have an explosion proof construction. 3.