Multi-Channel Controller Series PSE200, Pressure Sensor Series PSE530 CH kPa MPa kPa MPa MPa kPa kPa MPa kPa MPa OUT1 OUT2 CH 1 2 3 4 P R E S S U R E Copy function (page 14) Each channel's information can be copied to another channel.
L2 = 21 x m + 89.8 L1 = 10.5 x n + 45 Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Default settings At the time of factory shipment, the product is in "Remote Control Mode" and set to "Enable DHCP".
Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. Identification of flow rate range and standard or special product are displayed Tighten to the specified torque for piping. The tightening torque for connection threads is shown in the table below.
The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3.
Install an air filter, if necessary. Install air filters close to valves on the upstream side. Install an aftercooler or air dryer, if necessary. Compressed air that contains excessive drainage may cause malfunction of valves and other pneumatic equipment. To prevent this, install an aftercooler or air dryer, etc.
Never use in an environment where flammable fluid or gas is used. Since this is not an explosionproof construction, it may lead to an explosive disaster. Avoid repeatedly bending or stretching the lead wire. Wiring which applies repeated bending and tensile stress to the lead wire can break the circuit.
The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3.
Set value P_1 Fitting (width across flats: 24 mm) Hysteresis H_1 Pressure Switch ON At normal output Switch OFF Safety Instructions Time [s] Warning When tightening, do not hold the upper part of the product (Display) with a spanner. Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result.
Add 1 g for AC. ( ): Without sub-plate. 4-3-4 5 Series SY100 How to Order Standard type (Cv0.008) Light/Surge voltage suppressor Nil S Z R U Without light/surge voltage suppressor With surge voltage suppressor With light/surge voltage suppressor With surge voltage suppressor (Non-polar type) With light/surge voltage suppressor (Non-polar type) For AC voltage valves there is no S option.
S 1 p c . n n p c s . L Long leads uountng B Front Nose Mount C -Rear Pivot E -Double End K -Non-Rotating Rod R -Block Mount W-Double Rod Auto.Switch 853. D-853 Gsg D-G59 B54. D-854 K59 D-K59 864 .
Add 1 g for AC. ( ): Without sub-plate. 4-3-4 Series SY100 How to Order Standard type (Cv0.008) Light/Surge voltage suppressor Nil S Z R U Without light/surge voltage suppressor With surge voltage suppressor With light/surge voltage suppressor With surge voltage suppressor (Non-polar type) With light/surge voltage suppressor (Non-polar type) For AC voltage valves there is no S option.
For applications that require constant speed, select an applicable equipment for the level of demand.
Spacers are used to fix the stroke adjustment unit at an intermediate stroke position.
Also, when exceeding the air cushion stroke ranges on page 1191, the piston speed should be 100 to 200 mm/s. Note 2) The piston speed is 100 to 1000 mm/s for centralized piping. Note 3) Use at a speed within the absorption capacity range. Refer to page 1191.
Descrption Subplate Note VQZ100-S-01T 1 Body VQZ100 1/8" Aluminum die cast Metal seal VQZ200-S-01T Spool/Sleeve VQZ200 1/8" Stainless steel 2 Rubber seal VQZ200-S-02T Spool valve VQZ200 1/4" Aluminum/NBR 3 VQZ300-S-02T Piston VQZ300 1/4" Resin 4 VQZ300-S-03T Pilot valve VQZ300 3/8" 26 Base Mounted Type Series VQZ Dimensions: VQZ100 Dimensions: VQZ100 (mm) Valve Scale: 45% Grommet (G): VQZ115
~:;:--l' VAC Vacuum load lock chamber Digital pressure switch Digital Pressure Switch Series ZSE6/ISE6 (For vacuum) (For positive pressure) Model 1~SV(S % F ,S, ) ".
[r An] Select connected sensor [oFF] Unused Refer to the SMC website (URL http://www.smcworld.com) for more information about troubleshooting.
[F82] Input of line name No name [*] Flow (Temperature) Setting Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof. [F90] Setting of all functions OFF Temperature lower limit exceeded The fluid temperature is below -10 oC. Rise the fluid temperature.
If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product regularly for proper operation. Otherwise malfunction can result, causing an accident.