AWG When the handle is not easily locked, turn it left and right a little and then push it (when the handle is locked, the orange mark will disappear). Orange mark 37 Series AWG20K/30K/40K Construction AWG20K AWG30K/40K D B P C C A A K U P C S K O U H L to C S O H L to B D D-D C-C !0 o A-A B-B !1 !0 o e !1 e w w y y q q !2 !
Use a new sensor connector in case wiring or the snapping of A into B are done incorrectly. 2-M3 x 8L Tighten screws 1/4 to 1/2 turn after the heads are flush with the panel. When using 48 conversion adapter 48 conversion adapter (ZS-26-D) B A 4 3 2 1 4 3 2 1 4 3 2 1 Verify from the top side of A that the lead wires are inserted completely.
Auto switch model D-M9(V), M9W(V), A9(V) Port aperture Bore size (mm) A (Mounting groove number) B (Mounting groove number) C (Mounting groove number) D (Mounting groove number) A (2) (2) (2) 32 D B (2) (2) (2) 40 Diagram seen from the piston rod 50 (2) (2) (2) C 63 (2) (2) (2) Operating Range Auto Switch Mounting Auto switch model Bore size (mm) 32 40 50 63 D-M9, D-M9V D-M9W
Problem Possible cause Investigation method Countermeasure (1)Check if a current of 80 mA or (1)(2)Connect the load as more is flowing to the output. (2)Check if the connected load specified. satisfies the specifications, and if the load is shorted. (3)Use a relay with a surge Over current to the output (Er1 and 2) voltage suppressor or take a measure to prevent noise. (3)Check if a relay
SRP Note) A pressure gauge with a full span of 0.8 MPa is attached. SRF Symbol Relieving type Non-relieving type ITV IN IN 1 1 IC OUT OUT 2 2 ITVH OUT OUT 2 2 ITVX Note) A standard model is equipped with a backflow function. A main valve opens when the inlet pressure is released, and then an outlet pressure backflows into the inlet side.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
SUP. 3 1 2 3 1 2 3 1 2 E Padlock mounting position D C SUP J 2 2 x K A T IN OUT AA 3 L 2 x P1 (Port size) B V BB U Built-in silencer (Option) M (Width across flats) 3 N P2 (Port size) Q EXH Y Bracket (Option) R S X W Dimensions (mm) Standard specifications Model P1 P2 A B C D E F G H I J K L M 1/8, 1/4 1/4, 3/8 1/8 1/4 3/8 1/2 1/2 66.4 80.3 104.9 110.4 134.3 22.3 29.4 38.5 42 53 40 53 70
2(A) 2(A) 47.5 VHS 13.5 (A port) Rc 3/8 Individual exhaust: VV3PA5-42Station 3-03 28.5 3(R) 3(R) (R port) Rc 3/8 PA NO NC 87 (PA port) Rc 1/8 (Mounting hole) 2-7.2 30 PA 41.5 91.4 84.4 91.4 60 16.5 1(P) 41.5 PA (P port) Rc 3/8 (Pitch) 88 31 33 7.5 L2 L1 (PA port) Rc 1/8 PA 61.5 66 2(A) 2(A) 47.5 13.5 (A port) Rc 3/8 n: Station n L L1 L2 Formula L1 = 33 x n + 29 L2 = 33 x n + 14 6 227 212
DC24V 24VN SY100-82-3-05 DC12V 12VN SY100-82-3-06 AC100V 100VN SY100-82-2-01 AC200V 200VN SY100-82-2-02 2. After removing the holding screw, insert a flat head screwdriver, etc. into the notch on the bottom of the terminal block and pry it open, separating the terminal block and the housing.
When tightening is not sufficient, it will cause sealant failure or a loose fitting. 4. Re-using 1) Normally, a fitting with sealant can be re-used 2 to 3 times. 2) Remove the sealant material that is separated and adhering to a removed fitting with air blow, etc.
AL-OMQ0006-C PRODUCT NAME LUBRICATOR MODEL / Series / Product Number AL10-M5(-2,3,6,R,Z)-A AL20-(F,N)01(F,N)02(B)(-2,3,6,C,R,Z)-A AL30-(F,N)02(F,N)03(B)(-2,3,6,8,R,3W,Z)-A AL40-(F,N)02(F,N)04(B)(-2,3,6,8,R,3W,Z)-A AL40-(F,N)06(B)(-2,3,6,8,R,3W,Z)-A AL50-(F,N)06(F,N)10(B)(-2,3,6,8,R,3W,Z)-A AL60-(F,N)10(B)(-2,3,6,8,R,3W,Z)-A Contents Page 1. SAFETY INSTRUCTIONS 1-5 2. APPLICATION 6 3.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
Set bank 1, 2, & 3 inputs off. 2. Set point A input on. 3. Busy output is on while actuator homes. 4. Busy output turns otf, and origin return output turns on. 5. Set point A input off, and point A output turns off. Return to step #2 to reoeat.
Accessory (Option) /Part No. 0.2 to 1.0 MPa VEX Model VBA2200 Ambient and fluid temperature 2 to 50C (No freezing) VBA1110-1 VBA4100 VBA2100 VBA4200 Description AMR G27-20-R1 2 pcs. G46-10-01 2 pcs. G27-10-R1-X209 2 pcs. G27-10-R1-X209 2 pcs. G46-10-01 2 pcs.
wiring/Supply port right) IN Spacer Seal for additional station End plate L End plate R Y200-A ISA-7-B ISA-6-B ISA-7-A When a 2 port solenoid valve is connected to the right: ISA-6-A When 2 air catch sensors are connected or when a 2 port solenoid valve is connected to the left: Bracket ISA-4-A Straight, 5 m A pair consists 1 set.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.
AMX-OMY0038-A PRODUCT NAME Activated Carbon Filter MODEL / Series / Product Number AMK20-(F, N)01 ~ (F, N)02(B)(-2, 6, C, R, Z)-D AMK30-(F, N)02 ~ (F, N)03(B)(-2, 6, R, Z)-D AMK40-(F, N)02 ~ (F, N)04(B)(-2, 6, R, Z)-D Contents Page 1. Safety Instructions 2 to 7 2. Application 8 3. Standard specifications 8 4. How to order 9 5. Construction / Options / Replacement parts 10 6.
Rated pressure range A B ZSE3 0 to -101 kPa 0 -101 kPa ISE3L 0 to 98 kPa 0 98 kPa ISE3 0 to 0.98 MPa 0 0.98 MPa -25No.PS-OMO0002-A Dimensions Grommet type Z/ISE3-01/T1-26No.PS-OMO0002-A Connector type Z/ISE3-01/T1-C -27No.PS-OMO0002-A Single-installation type Grommet type ZSE3-0X-28No.PS-OMO0002-A ZSE3-0X--D -29No.PS-OMO0002-A Connector type ZSE3-0X-C -30No.PS-OMO0002-A ZSE3-0X-C-D -31No.PS-OMO0002
Option Rated voltage Voltage symbol Part no. 100 VAC 100V VK300-82-2-01 110 VAC 110V VK300-82-2-03 200 VAC 200V VK300-82-2-02 Note) When requiring a gauge different than that mentioned above, specify the model number. 220 VAC 220V VK300-82-2-04 Option is packed with it.
Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2.