VG342 Since PE port is the exhaust port of the pilot valve, do not attach a plug or reduce the port diameter. 2. X port is the pressure supply port of the pilot valve and PE port is the exhaust port of the pilot valve. Avoid mismatching when piping. 3. The manual portion contains a breather hole for the core.
Pressure gauge SMC 1 P 5 3 R2 R1 D side PE Pressure Setting Caution 1. Set the pressure of an interface regulator using a flat head screw driver. 2. The pressure adjustment is increased by turning clockwise and decreased by turning counter clockwise. Perform pressure setting by increasing from low pressure to the desired setting. 3.
AC G H G H Grommet (G), (H): SYJ3120-M3 With bracket: SYJ3120-M3-F G: Approx. 300 H: Approx. 600 (Lead wire length) 54.4 [56.6] 28.4 32.2 22 2-3.5 (For mounting) 3.2 7.1 13.2 16.4 10 + 8.2 A B 4 19.3 7 11.5 Manual override 34.7 [41.7] M5 x 0.8 (A, B port) 2-1.8 (For manifold mounting) (Light/Surge voltage suppressor) 28 [35] + 22.1 54.4 [56.6] 2 13.5 12.6 15 R P R (Bracket) 15 11 10 1.2 (PE
Can be grounded with the PE line of the power supply cable. Also, do not use together with equipment that generates a strong electrical magnetic noise or high frequency noise. 5. Wiring cable should be handled with care. Do not bend, twist or stretch the cord or cable. 6. Wire with an applicable size cable and terminal.
X, PE port PCW type There is no need to enter anything when the SUP/EXH block mounting position M is selected. Pilot spec.
Appearance Terminal block For wiring, please refer to P.2-5 10,11Remote control 12,13Operation 14,15Failure L1,L2,L3: Power supply PE: Ground 15 14 13 12 11 10 PE L3 L2 L1 Customer Connection Side Customer Connection Side Terminal connecting screw: M3 Terminal connecting screw: M5 Crimped terminal width: 6.5mm or less Crimped terminal width: 13mm or less Applicable electric wire: 8mm 2
Out connector with spanner during piping. 5 Wait 3 minutes before restart. 6 Ensure Running Condition / Evaporating Temp. in green zone. 1 2 3 4 5 6 i 5 IDH Series i.2 IDX-OM-W038 i i.3 HFC i 6 IDH Series i.3 IDX-OM-W038 i i.4 1 1.5 () i.4 i 7 IDH Series IDX-OM-W038 1. 1 1.1. 1-3 10mm 17mm (22mm) 17mm (22mm) IDH Series 11 1.1 IDX-OM-W038 1. () OFF ON () 3 7 6 5 1 2 4 PE
1) 1) 1) 1) 2) 2) 2) 2) PE PE (AMC ) 3 3 3 3 (A,B) (N.C.)N.O.3 3 B (CYL.1) A (CYL. 2) N.C.
As the PE port is the exhaust port of the pilot valve, do not plug or restrict it. 2. The X port is the pressure supply port of the pilot valve and PE port is the exhaust port of the pilot valve. Pay attention that these ports should be connected correctly. 7 VG300**-OMH0006-A Trouble shooting Perform troubleshooting with higher possibility based on the failure phenomenon.
(included) M3 x 6l Binding band (included) 34 Holding plate (included) 4-M6 x 1 C section 30 D When using a PE terminal, use accessories included as shown above.
AC G H G H Grommet (G), (H): SYJ3120-M3 With bracket: SYJ3120-M3-F G: Approx. 300 H: Approx. 600 (Lead wire length) 54.4 [56.6] 28.4 32.2 22 2-3.5 (For mounting) 3.2 7.1 13.2 16.4 10 + 8.2 A B 4 19.3 7 11.5 Manual override 34.7 [41.7] M5 x 0.8 (A, B port) 2-1.8 (For monifold mounting) (Light/surge voltage suppressor) 28 [35] + 22.1 54.4 [56.6] 2 13.5 12.6 15 R P R (Bracket) 15 11 10 1.2 (PE
This is not a clean room series product. 4 MACM Series Dimensions W (Workpiece loadable range) 4 x D At maximum offset (A + 2 x S) S F DB DA C X114 X115, X116 U B W A H T H Q PB E PA PD P (Unlocking port) PE P (Locking port) P (Relief port) (Option V only) MACM4, MACM6 MACM2, MACM10 PC PC PC PC PE P (Relief port) (Option V only) PD [mm] Dimensions Model A B C D DA DB E F H P PA PB PC PD
The built-in circulator tank is made of resin (PE). Therefore, the tank may be crushed if the pressure is negative. Special attention must be paid if the flow rate of the circulating fluid is high. To avoid a negative pressure of 0.02 MPa or below, the piping return should be as thick and short as possible to minimize piping resistance.
Hz L/min 55/68 Maximum pump head m 50 Minimum operating flow rate 50/60 Hz7 L/min 29/45 Tank capacity L 18 Circulating fluid outlet, circulating fluid return port Rc1 (Symbol F: G1, Symbol N: NPT1) Tank drain port Rc1/4 (Symbol F: G1/4, Symbol N: NPT1/4) Pump capacity Fluid contact material Stainless steel, Copper (Heat exchanger brazing), Brass, Bronze, PTFE, FKM, EPDM, PVC, NBR, POM, PE
50 Settable pressure range Note 6) MPa 0.1 to 0.5 Minimum operating flow rate Note 7) L/min 20 Tank capacity L 18 Circulating fluid outlet, circulating fluid return port Rc1 (Symbol F: G1, Symbol N: NPT1) Tank drain port Rc1/4 (Symbol F: G1/4, Symbol N: NPT1/4) HEA Pump capacity IDH Fluid contact material Stainless steel, Copper (Heat exchanger brazing), Brass, Bronze, Carbon, Ceramic, PE
Be sure to leave it open as if the PE port is blocked, normal pressure setting cannot be performed.
Note 1) Air consumption is approx. 9.5 L/min (ANR) [at a supply pressure of 1.0 MPa].
Note 2) If there is an abnormal amount of air leakage from the PE port, the diaphragm may be damaged.
VALVE, SOL, BASE MT (DC), VALVE, SYJ500 SOLENOID VALVE 3/PORT, 2A, SYJ500 NO SIZE RATING, .18794 lb
SMC has improved product performance and reliability with the redesigned SY series valve. The SY3000 and SY5000 have the same valve width as their predecessors, but the flow has been increased by up to 80%, allowing the valve size to be reduced. A built-in strainer in the pilot valve prevents trouble caused by foreign matter. By using H-NBR seal material for the main valve and seals, Ozone
SMC has improved product performance and reliability with the redesigned SY series valve. The SY3000 and SY5000 have the same valve width as their predecessors, but the flow has been increased by up to 80%, allowing the valve size to be reduced. A built-in strainer in the pilot valve prevents trouble caused by foreign matter. By using H-NBR seal material for the main valve and seals, Ozone
SMC has improved product performance and reliability with the redesigned SY series valve. The SY3000 and SY5000 have the same valve width as their predecessors, but the flow has been increased by up to 80%, allowing the valve size to be reduced. A built-in strainer in the pilot valve prevents trouble caused by foreign matter. By using H-NBR seal material for the main valve and seals, Ozone