Multistage Ejector ZL-OM00801 Contents Safety Instructions 2 Model Indication and How to Order 10 Mounting and Installation 12 Air Supply 12 Supply Pressure 13 Piping 13 Solenoid Valve 15 Construction 15 Maintenance and Inspection 17 Exhaust from Ejector 19 Specifications 19 Circuit Diagram 22 Weight 23 Exhaust Characteristics and Flow Characteristics of Ejector 24 Flow Characteristics Curves 25 Vacuum Pressure
20 25 30 15.0 11.5 23.0 10 5 10 15 20 25 30 35 40 45 18.0 10.5 21.0 16 5 10 15 20 25 30 35 40 45 20.0 13.0 26.0 * The above numbers are references for the mounting positions of those auto switches that detect a stroke end.
Note 1) Tighten within the tightening torque of 0.5 Nm +/-15%. Note 2) Cable (7) external: 6 to 8 mm (1) (2) (6) (5) (4) (3) (7) (8) (11) (9) (10) Figure-1 9 VG300-OMH0002-B TROUBLE SHOOTING Should any trouble be found during operation, trace the source of the trouble in the following or der and take correcitve action.
If the heater 0 5 10 15 20 25 30 temperature is over 200oC or valve temperature is Time (sec.) Time (sec.) ( Duration of the inrush current flow (as a guide) Duration of the inrush current flow (as a guide) over 150oC, please use thermostat to control the heaters to prevent overheating.
Basic Circuit for Cylinder Operation 15 5. Troubleshooting 16~17 6. Construction and Material 18~23 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
DIMENSIONS 15 REGULATOR Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Maintenance and Inspection 3.1 Inspection -P. 15 3.2 Maintenance -P. 15 3.3 Replacement Parts -P. 15 4. Troubleshooting -P. 16 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
*In the case of N.O. specification, 1(P) port. (15) Supply specified pressure to X port. (Single solenoid, 3 position: 0.2 to 0.9 MPa, Double solenoid: 0.1 to 0.9 MPa) If no improvement is achieced in spite of the above countermeasure, inside of the valve may have some abnomality. In this case, stop using the balbe immediately.
No.PS-OMR0002-K PRODUCT NAME Digital Gap Checker MODEL / Series / Product Number ISA3 series Table of Contents Before Use Safety Instructions 2 Features 7 Model Indication and How to Order 8 Summary of Product parts 14 Specification 15 About this product Specifications (ISA3) 15 Specifications (Regulator) 16 Specifications (2 port solenoid valve) 16 Characteristics graph 17 Dimensions
Operating force to act and separate piston slider and Model pressure limit (mm) (MPa) external slider from each other. 6 CY3B6 0.55 10 CY3B10 0.55 4-2) Consider the following points to realize 15 CY3B15 0.65 intermediate stop in pneumatic circuit. 20 CY3B20 0.65 25 CY3B25 0.65 a) Intermediate stop realized by the rodless 32 CY3B32 0.65 cylinder is not high accurate.
AC coil VEX1101, VEX1201, VEX1301 20% or less of rated voltage VEX1501, VEX1701, VEX1901 15% or less of rated voltage The valves presented in this catalog are not designed for safety applications such as an emergency shutoff valve. If the valves are used for the mentioned applications, additional safety measures should be adopted. 3.
Rotate the pressure gauge cover 15 degree counterclockwise to pull out the pressure gauge cover. AW20(K) AW30(K) AW40(K) AW60(K) 2) Remove the pressure gauge. Rotate two mounting screws counterclockwise with Phillips head screw driver to remove the pressure gauge and two mounting screws.
15 15 17 (Workpiece adsorption port) 6.4 6.4 58 6.4 74.2 A (Refer to the figure below.) 6.8 66 58 58 Auto switch mounting groove on workpiece adsorption side Rc1/8 (Workpiece release port) Bumper (9.8) (26.5) (25.1) 50 50 (4) 50 D-P3DWA D-M9V With auto switch Symbol Part number A B C T 1 MHM-32D1-X6400 80.2 39 A T (6) 2 MHM-32D2-X6400 81.2 30 (7) 3 MHM-32D3-X6400 82.2 (8) 50 B C Bumper dimensions
Refer to pages 12-15-3 to 12-15-4 for Safety Instructions and Common Precautions on the products mentioned in this catalog, and refer to pages 12-1-4 to 12-1-6 for Precautions on every series. Warning If a workpiece is hooked onto the attachment, make sure that excessive impact will not be created at the start and the end of the movement.
B G P BG GP 1 Specialty Regulators ARX Series Regulator for 290 psi (2 MPa) ARX20, 21 Flow Characteristics ARX20-N02 130.5 ARX20-N01 Conditions: Supply pressure 290 psig 130.5 116 116 101.5 101.5 Secondary pressure (psig) Secondary pressure (psig) 87 87 72.5 72.5 58 58 43.5 43.5 30 30 15 15 0 3.5 7.1 10.6 14.1 17.7 21.2 24.7 28.3 31.8 35.3 0 3.5 7.1 10.6 14.1 17.7 21.2 24.7 28.3 31.8 35.3
Flow (l/min (ANR)) Flow (l/min (ANR)) Effective area (mm2) Effective area (mm2) Flow (l/min (ANR)) 300 06 1.0 2 4 200 50 100 0.5 1 2 100 0 0 0 0 5 10 0 5 10 0 5 10 Needle rotation (Turns) Needle rotation (Turns) Needle rotation (Turns) ASD530F ASD630F 1000 1500 14 20 10, 11 12 Flow (l/min (ANR)) Effective area (mm2) Effective area (mm2) Flow (l/min (ANR)) 12 1000 10 8 10, 11, 12 08, 09 15
bending radius 80 3.4 13 4.5 6 Series ITV0 Dimensions Single unit for manifolds 56 50 PWR ERR M8 x 1 Cable connection threads 15 15 9 84 86 3.7 Breathing hole Note) (M3 x 0.5) OUTx OUT port (4, 5/32") 8 2 5 18.5 Note) When used under the conditions equivalent to IP65, use the regulator after piping a fitting/tube into a breathing hole.
) M5 x 0.8 34 2-3.5 Manual override (Mounting hole pitch) (For mounting) (Non-locking) 8 10.6 9 A 1 32 24 15 X 24.5 18.6 (37) (30) 1 1.5 14.5 3 R P 23 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 21 34 4 33 42 4 4 2-2.6 (2.3) 39 (25) (18) 46 (For mounting) 2-M3
Note) Tighten within the tightening torque of 0.5 Nm 15%. Note: a It is possible to wire even in the state of bare wire.
VR D E F G J K C 18 1(P) 2(A) 4 4 VHK-04F-04F VHK-06F-04F VHK-06F-06F VHK-08F-06F VHK-08F-08F VHK-10F-08F VHK-10F-10F VHK-12F-10F VHK-12F-12F 31.5 21.8 17.5 3 port valve 41 3.5 1 27 22 26 47.6 23.8 23.8 16.5 15.8 15.8 11 3.4 1.2 15 VHK-B1A 44.5 14.5 16.5 VH 18 6 4 6 41 48 48.6 24.3 23.7 16.5 3.5 16.8 15.8 11 5.1 1.2 15 16 VHK-B1A 44.5 14.5 1 27 22 16.5 26 24.3 16.8 7.2 18 8 6 8 41 50.5 52.4