Series VCL Install a suitable filter (strainer) immediately upstream from the valve. As a general rule, use 80 to 100 mesh. Caution 1.
Temperature Data A or B = Series IDUS: Data A Series IDFS: Data B Air pressure Data C = 2 Calculate corrected air flow by using A or B and C. Corrected air flow = (Air flow) (Data A x Data C) Corrected air flow = (Air flow) (Data B x Data C) 3 Select a model having an air flow capacity that is higher than the corrected air flow.
lubricant that has a shielding effect from ozone.
IP8000-011-AG) Note 3) A is applied to approx 90cm3-capacity actuator. B is applied to approx 180cm3-capacity actuator. Note 4) Standard lever is not attached. Note 5) It is to be used together with A or B when tending to overshoot by the use of A or B. It is mounted to the body as a replacement of the standard compensation spring. Note 6) With terminal box, Non-explosion proof.
Using a regulator on the secondary side When mounting a regulator on the secondary side (A port side), use a residual pressure relief regulator (AR2550 to 4050) or a check type regulator (AR2560 to 6060). With a standard regulator (AR1000 to 6000), the secondary side pressure may not be released when this valve is exhausted. 5.
Leakage voltage Particularly when using a resistor in parallel with a switching element and using a C-R element (surge voltage suppressor) to protect the switching element, take note that leakage current will flow through the resistor and C-R element, etc., creating a danger that the valve may not shut OFF.
A counter clockwise until it stops (approx. 45). 4) Install a new element on cover A and insert it into the case.
or more for Air pressure lock-up Sol A, B & C accept direct-operated type or pilot operated type. As you find that Solenoid valve Sol A for lock releasing is independent, you can use a compact 3-way valve and mount it dkeclly io lock-po[i by means of a nipple so that you can get the time delay of locking as short as possible. Diagram 6.
Use of a sensor gives a wider control range. 3. Stabilization of the Electropneumatic Proportional Valve's Performance The adoPtion of a constant current system enables a stabilized performance even with a change in impedance or voltage at the power source. The repeatability is also improved.
If the stain is persistent, soak a cloth in a dilute solution of neutral detergent and wring it out tightly before using it to wipe the product. Afterwards, finish wiping with a dry cloth. Other Caution 1.
^-'-t" +'' l' tv."' 2',Sr " ,:; . a . ' li'J.Sh.' A--T.Tr/ir.{ 8r " 4 ' l e A . a ' A . , .
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
CAT.ES13-7 A Exhaust Cleaner for Clean Rooms Series AMP An exhaust cleaner that can be used inside a clean room. Series AMP Exhaust Cleaner for Clean Rooms An exhaust cleaner that can be used inside a clean room Exhaust air cleanliness: Equivalent to Class 100 (Consult SMC in advance, as this will differ depending on the operating conditions.)
A A afll-'h s-zl;lh P R P R (external pilot type) A A , A;Tt-Zb gzt;]ri! , P R P R Model Specifications Air and inert 20-100 PSI (1.5"7kgf/cm,) VAC-1 10Torr 20-1OoPS|(15-7ksflcm'?) N,lax. 120'F (50'C) 20 ms or less (7OPS|) 600 cpm , Slotted Knob locking type Individual, Common Not (Use turbine oil # 1 (lSO VG32) if lubrication is Drovided.)
igs 3 wiE slslem lwhen Dower source lor slrlbh and load is commod) Contact capacity a Loads overthe minimum contactcapacity of the switch should not be used. I t r i : : O _ _ a r ! P ! ! : o : L o a d F = I Ll|acxo re 3 riire syslom (Wren pol9l sqJme lor swioh and load s nol cofimom) Fled ^ | | ,.,",.-" a-a ao | | :".'*: ' "l Load l *lrlii + | | t r a ! ! !
Input a set value for pressure to perform switch output.
This prevents discharge to the outside for a fixed time. Element service indicator (optional specification) With indicator function The element life (standard) can be visually confirmed. First element (main element) Element service indicator Element clogging is detected by a pressure differential, and indicated by a red symbol.