Multi-channel Digital Sensor Monitor -segments, 7-segments for other) Number of display digits Sub display (right): 5 digits (partially 11-segments, 7-segments for other) Operation light LED is ON when switch output is ON (OUT1, OUT2: Orange) Digital filter 5 Variable from 0 to 30 s/0.01 s increments -79No.PS-OMW0005-C Product No.
(Refer to page 11.) 1) If a lubricant is used in the system, use class 1 turbine oil (no additive), ISO VG32.
Since cylinders receive excessive force in such a case, do not design circuit synchronizing cylinders only. 11. Mounting Methods Various mounting methods are available as follows. Bottom mounting Side mounting 11-1. Cautions on Mounting 1) Never place your hands or fingers between the plate and the body.
Auto switches When an auto switch is mounted or its set position is changed, refer to pages 11 to 17. Caution Use a specific mounting bracket (Table 3 on page 12.) and mount the product so that the band of the bracket will be perpendicular to the stroke of the product. Tighten mounting screws to the appropriate torque.
0.13 the values in the table 11. 20 0.24 Piston speed has to be less than the allowable value 25 0.45 32 0.88 40 1.53 23/28 6.
As shown in Fig. 11, hold the piston seal with one hand and push it into the groove so that the piston seal can be lifted off and pulled out without using a precision screwdriver. The groove of the rod cover is deep, so if the rod seal is removed with a precision screwdriver, it might be damaged. Fig 10. Remove rod seal Pinch and pull out Fig 11.
Refer to the Material Safety Data Sheet (MSDS) of the hydraulic fluid when supplying the fluid. 11 - 3. Maintenance 3-1. Precautions Warning 1. Maintenance should be performed according to the procedure indicated in the Operation Manual. If handled improperly, malfunction and damage of machinery of equipment may occur. 2. If handled improperly, compressed air can be dangerous.
The value of the residual pressure can be checked using the outlet pressure gauge. 11.
MHCM2-7S D8.3 205.2 2-M2 x 0.4 thread (Mounting thread) 2-M2 x 0.4 depth 4 (Mounting thread) 2.5 2 1.5 When open 20 When closed 7 10 6 4.5 15 11 7.7 1.8 16.5 6 100.05 (23) M3 x 0.5 (Finger closing port) 2-M2 x 0.4 thread (Attachment mounting thread) 4 0 0.03 3 12-8-23
MHCM2-7S D8.3 205.2 2-M2 x 0.4 thread (Mounting thread) 2-M2 x 0.4 depth 4 (Mounting thread) 2.5 2 1.5 When open 20 When closed 7 10 6 4.5 15 11 7.7 1.8 16.5 6 100.05 (23) M3 x 0.5 (Finger closing port) 2-M2 x 0.4 thread (Attachment mounting thread) 4 0 0.03 3 12-8-23
PP depth element Nominal filtration accuracy: 1 to 75m Material: PP EJ202S ... x 11 (L125) EJ302S ... x 11 (L250) EJ402S ... x 11 (L500) b Set the stopper on the retainer while holding down the V-band outside perimeter, and then tighten the wing bolt to the prescribed position.
Nil T F Rc NPTF, NPT G Caution 3 position closed center 3 position exhaust center Refer to pages 5-11-2 to 5-11-6 for Safety Instruction and Solenoid Valve Precautions. 5-3-1 2 Series VZA2000 Dimensions: Body Ported 2 position single: VZA2121-M5 2 position double: VZA2221-M5 2-2.8 mounting hole 2-2.8 Mounting hole Pilot port (A side) M5 x 0.8 Pilot port (A side) Pilot port (B side) 2-2.8
Installation. 11 2. Hardware Specification. 3 1. Introduction. 1 3.1 DIN RAIL Mounting . 11 3.2 Termination at Screw Terminals . 11 3.3 Installation Mounting Notes. 12 2.1 Available Models. 3 2.2 Power Supply Specification . 4 2.3 Input Specification. 5 2.4 Output Specification. 7 2.5 General Specification. 8 iii PneuAlpha 4. Wiring . 13 6.
The example screen shown at the right shows that the Output will turn ON at the following times: The rst week of the month on Monday, Wednesday, and Saturday at 11:30 AM. The third week of the month on Monday, Wednesday, and Saturday at 11:30 AM.
Frequency (Hz) 50 60(53) 18 60 51(44) 12 Model Power source VX3 7.5 6 8 11 9.5 11.5 AC VXZ22 VXA DC 50 80 21 60 67 17 AC VXZ23 VN DC LVC JIS Symbol LVA OUT LVH IN LVD N.O.
Refer to pages 15-18-3 to 4 for Safety Instructions and Common precautions on the products mentioned in this catalog, and refer to pages 15-1-10 to 11 for Precautions on every series. Min. bending radius (mm) 12 15 23 27 31 60 12 15 23 30 40 Operating temperature 20 to +60C (No freezing) Nylon 11, Nylon 12 Material Caution 1.
CEP: 09950-350, Brasil TEL: 11-4051-1177 FAX: 11-4071-6636 GREECE (Distributor) S.Parianopoulos S.A. 7, Konstantinoupoleos Street 11855 Athens, Greece TEL: 01-3426076 FAX: 01-3455578 DENMARK SMC Pneumatik A/S Knudsminde 4 B DK-8300 Odder, Denmark TEL: 70252900 FAX: 70252901 COLOMBIA (Distributor) Airmatic Ltda. Calle 18 69-05 Apart.
Fittings & Tubing Air Cylinders Rotary Actuators How to Order Clean series 11 12 Vacuum suction type Relief type (with specially treated sliding parts) CXSJM, CXSJL CXSJL CXS 6 50 J 11 L M9B S 21 CXS L J 6 50 M9B S Number of auto switches 2 pcs. 1 pc. n pcs.
Note 11) : For thread type: NPT only.
(Refer to page 11, [I/O cable] for details.) Note 3) The DIN rail is not included. If the DIN rail is required, please order separately.