CE2 NO YES Do you have any problem, even if it might run over the target position? (Overrun) NO Do you have any problem, although an error might occur if it is set to be (number of trial again = 0) in order to prevent from doing a trial again when positioning is done at the outside of the range? During the positioning operation, there may be the case it needs to do overruns or trials again.
NO YES Do you have any problem, even if it might run over the target position? (Overrun) NO Do you have any problem, although an error might occur if it is set to be (number of trial again = 0) in order to prevent from doing a trial again when positioning is done at the outside of the range? During the positioning operation, there may be the case it needs to do overruns or trials again.
It may cause injury to personnel. 5) Do not use the product to clean or remove toxic substances or chemicals. 6) Do not drop, step on or hit the product.
Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
Symbol Stations 02 08 2 stations 8 stations 2 stations 8 stations 1 3 2 D side U side Stations G: Flat ribbon cable (PC wiring, with power supply terminal) Symbol Stations 02 08 2 stations 8 stations SS3J3-V60PD2-06D 1 set (Manifold part no.)
Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
Note) Do not change the rated voltage. VFS VS4 Series VFR2000 VQ7 Pilot valve assembly Tightening Torque for Mounting Bolt EVS Thread M3 (2 pcs.) M3 (3 pcs.) M3 (3 pcs.) M4 (4 pcs.)
Do not use in atmospheres where the valve is in direct contact with corrosive gases, chemicals, salt water, water or steam. 2. Do not use in locations subject to vibration or impact. Confirm the specifications in the main section of the catalog. 3. Use a protective cover, etc., to shield valves from direct sunlight. 4.
Note 2) When using the D-M9lA, D-M9lAV or Y7BA, do not use the steel set screws which are included with the above auto switch mounting brackets (BA7-lll, BA4-lll).
Note 3) Specify the wiring specifications on the manifold specification sheet. 01 1 station Note) 08 16 8 stations (Double) 16 stations (Single) NKE Corp.: Uni-wire H System Note) Note) For details, refer to page 2-4-29.
Type A mounting bracket Type B mounting bracket 32, 40 YU-03 YA-03 YB-03 25 50, 63 YU-05 YA-05 YB-05 40 Material: Precision die-casting material equivalent to stainless steel 304 80 YU-08 YA-08 YB-08 90 Bore size (mm) O M J E D B Part no. 100 YU-10 YA-10 YB-10 160 K (Width across flats ) YB-03 32, 40 11.5 depth 7.5 34 9 25 7 12 H (With locking) YB-05 50, 63 14.5 depth 8.5 42 11 32 9 12 YB
Do not wipe out the grease in the sliding part of the air cylinder.
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water steam is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in a place subject to heavy vibration and/or impact. 3. Do not use in an environment where flammable gas or explosive gas is present. Usage may cause a fire or explosion.
Nylon tube Within 0.1mm Soft nylon tube Within 0.1mm Polyurethane tube Within+0.15mm, Within -0.2mm Do not use tube which do not meet these outside diameter tolerances.
In a locked state, do not apply impacts, strong vibrations or rotational forces. Do not apply a impacts, strong vibrations or rotational forces from external sources, because this could damage or shorten the life of the lock unit. 4. The locking of the fine lock cylinder is directional.
In a locked state, do not apply impacts, strong vibrations or rotational forces. Do not apply a impacts, strong vibrations or rotational forces from external sources, because this could damage or shorten the life of the lock unit. 4. The locking of the fine lock cylinder is directional.
D Plug-in Reducer: KPQR, KPGR Applicable tubing D Effective area mm2 Note 1) D Model L TPH TPS Applicable fitting size d Applicable tubing O.D. mm Weight g M A KPQR04-06 KPGR04-06 38.4 19.1 3 6 4 M A L 17 4 4 10.4 KPQR04-08 KPGR04-08 40.9 19.2 4 8 KPQR06-08 KPGR06-08 41.5 19.8 4 6 12.8 18.5 10 10 KPQR06-10 KPGR06-10 44 20.2 5 Applicable fitting size d 10 KPQR08-10 KPGR08-10 46 5 8 15.2 20.5
Do not use in a location having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. Do not use in locations where radiated heat will be received from nearby heat sources.
Do not use in locations where static electric charges will be a problem. Please consult with SMC regarding use in this kind of environment. 2. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire. 3. Do not use in environments where there is direct contact with liquids such as cutting oil, lubricating oil or coolant oil, etc.