• Inch' size I0 1/4" 03/8' 05/16" 05/16" diameter . . 03/S' 051160 1/2" Flbw."rate tlin\~ 330 750 350 C ,oP/rolled flow . (A,MR~~N '(lmjQ' . 180 600 1100 1190 [Ereo flaw) Effettive ~IOnal 11.6 17 2.9 5.2 18.4 5.4 9.3 'ttrea mm 2 . N01e} The iMicaled 110w rate values are al a pressure 01 O.5MPa and a temperature 01 20 Q C. 1 Speed Controller 5 .
Do not turn the piston rod with the rod boot kept locked. When turning the piston rod, loosen the band once and do not twist the rod boot.
Do not work when intoxicated or feeling ill. Accidents may occur if disregarded. Do not remove a panel unless permitted in this manual.
Do not remove cover panels that are not designated in this manual.
For AC specifications, Nil is only set for electrical entry DO.
Do not operate beyond the rated voltage range. If applying voltage over the rated voltage range, equipment may be damaged. 2. Avoid incorrect wiring such as polarity of power supply. Otherwise, equipment may be damaged. 3. Do not short circuit the load. (Do not connect to power supply.) Otherwise, equipment may be damaged.
Do not drop or bump the product. Dropping or bumping while handling may cause damage to the product. 5. Lead wire dimensions Covering: 3.4 Insulator: 1.1 Conductor: 0.64 Pressure Supply Warning 1. Do not use the switch with corrosive gas or liquid. Operating Environment Do not use the switch with corrosive gas or liquid. Such gas or fluid may cause damage to the switch. Warning 2.
Do not drop or bump the product. Dropping or bumping while handling may cause damage to the product. 5. Lead wire dimensions Covering: 3.4 Insulator: 1.1 Conductor: 0.64 Pressure Supply Warning 1. Do not use the switch with corrosive gas or liquid. Operating Environment Do not use the switch with corrosive gas or liquid. Such gas or fluid may cause damage to the switch. Warning 2.
Do not manipulate or perform settings with wet hands. Performing such activity will likely cause an electrical shock. 2. Do not use this product in the presence of a magnetic field. Use in such an environment is likely to cause a malfunction. 3. Do not use this product in an atmosphere containing an inflammable gas, explosive gas, or corrosive gas.
Do not apply excessive lateral load to the piston rod.
Do not work when intoxicated or feeling ill. Accidents may occur if disregarded.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water vapor is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in an explosive environment. 3. Do not use in a place subject to heavy vibration and/or impact. 4. The valve should not be exposed to prolonged sunlight. Use a protective cover if necessary. 5.
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water vapor is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in an explosive environment. 3. Do not use in a place subject to heavy vibration and/or impact. 4. The valve should not be exposed to prolonged sunlight. Use a protective cover if necessary. 5.
The lock might not disengage or might become damaged if a load ratio of 50% is exceeded. t Do not synchronize multiple cylinders. Do not operate two or more end lock cylinders synchronized to move a single workpiece because, one of the cylinder locks may not be able to disengage when required. y Operate the speed controller under meter-out control.
The lock might not disengage or might become damaged if a load ratio of 50% is exceeded. t Do not synchronize multiple cylinders. Do not operate two or more end lock cylinders synchronized to move a single workpiece because, one of the cylinder locks may not be able to disengage when required. y Operate the speed controller under meter-out control.
Do not use in locations having an explosive atmosphere. 2. Do not operate in locations where vibration or impact occurs. 3. In locations near heat sources, block off radiated heat. LVA LVH LVD LVQ When the tubing is curved, straighten it out before using it. Maintenance The tubing may slip if there is oil or dust, etc., on the holder.
Description BA-01, BA-02, BA-32, BA-04, BA-05, BA-06, BA-08, BA-10 BA2-020, BA2-025, BA2-032, BA2-040 BA5-050, BHN2-025, BSG1-032 BH2-040, BH2-050, BH2-080, BH2-100 BAF-32, BAF-04, BAF-05, BAF-06, BAF-08, BAF-10 BJ2-006, BJ2-010, BJ2-016 BM2-020A, BM2-025A, BM2-032A, BM2-040A BMA2-020A, BMA2-025A, BMA2-032A, BMA2-040A, BMA2-050A, BMA2-063A BHN3-025A, BHN3-032A, BHN3-040A D-B5, B6 D-G5, K5
Do not use in an atmosphere where corrosive gases, chemicals, sea water, water, or water steam is present. Do not use in cases where there is direct contact with any of the above. 2. Do not use in a place subject to heavy vibration and/or impact. 3. Do not use in an environment where flammable gas or explosive gas is present. Usage may cause a fire or explosion.