Series: VQ20, Stations: 14 Stations, Option: DIN Rail Mount w/o DIN Rail, Thread: NPT3/8
Series: VQ20, Stations: 16 Stations, Option: DIN Rail Mount w/o DIN Rail, Thread: NPT3/8
Series: VQ20, Stations: 20 Stations, Option: DIN Rail Mount w/o DIN Rail, Thread: NPT3/8
Series: VQ20, Stations: 5 Stations, Option: DIN Rail Mount w/o DIN Rail, Thread: NPT3/8
Series: VQ20, Stations: 8 Stations, Option: DIN Rail Mount w/o DIN Rail, Thread: NPT3/8
Series: VQ20, Stations: 10 Stations, Option: DIN Rail Mount w/o DIN Rail, Thread: NPT3/8
Series: VQ20, Stations: 3 Stations, Option: DIN Rail Mount w/o DIN Rail, Thread: NPT3/8
Series: 2 (VQ20), Stations: 3 Stations, Option: DO (DIN Rail Mount w/o DIN Rail), Thread: 00N (NPT3/8)
Stainless Steel Heat Do not use with fluids other than compressed air. Cleaning equipment is designed exclusively for use with compressed air. Contact SMC in advance if a fluid other than compressed air is to be used. 2. Do not use compressed air which contains chemicals, organic solvents or corrosive gases.
Do not use in an atmosphere having corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not operate in locations where vibration or impact occurs. 3. In locations which receive direct sunlight, provide a protective cover, etc. 4. In locations near heat sources, block off any radiated heat. 5.
If the tubing is inserted without holding the elbow, excessive force can be applied to the valve and fitting assembly, causing air leakage or damage, etc. 1) Nylon tubing within 0.1 mm 2) Soft nylon tubing within 0.1 mm 3) Polyurethane tubing within +0.15 mm, within 0.2 mm Do not use tubes which do not meet these outside diameter tolerances.
AXT632-69-1 AXT632-69-2 VVCA30-3A-04-2 VVCA30-3A-04-1 OR-2200-200-H VCA35--VVCA30-6-n VVCA30-4A-04-2 VVCA30-4A-04-1 Material Part no.
Do not use tools, such as pliers, to rotate the knob. This can cause the idle rotation of the knob or damage. 3. Do not overtighten the lock nut. It is possible to tighten the lock nut (hexagon) manually. When tightening further with tools, tighten by approximately 15 to 30. Overtightening may cause breakage.
Do not lift the product by holding the panel, fittings or piping. Never lay the product down for transportation. This may lead to damage to the product. Do not modify the standard product using any of the optional specifications once the product has been supplied to a customer. Check the specifications carefully before selecting an air dryer.
Do not drop or bump the product. Dropping or bumping while handling may cause damage to the product. 5. Lead wire dimensions Pressure Supply Warning Covering: 3.4 Insulator: 1.1 Conductor: 0.64 1. Do not use the switch with corrosive gas or liquid. Do not use the switch with corrosive gas or liquid. Such gas or fluid may cause damage to the switch. Operating Environment Warning 2.
Refer to 4.3.2 Setting and checking,5.3.2 Setting and checking. 2 2 R D R D 3 3 S D S D 5 5 S G S G Master This product Do not connect any wire to other PIN numbers.
The switches shown DO NOT come with Yoke Clips attached.
The load ratio is obtained by the following formula: ((Load mass x 9.8)/Theoretical output) x 100% Conditions MB, CA2 series CS1, CS2 series Series Condition 10A x 1 m SGP (Steel pipe) dia. x Length VQ4100--03 VQ4101--03 AS420-03 Speed controller AN30-03 Silencer 10A x 1 m SGP (Steel pipe) dia. x Length VQ5100--04 VQ5101--04 AS420-04 Speed controller AN40-04 Silencer 448 INDEX Page 446 Base
Do not apply excessive lateral loads to the piston rod.
not occur on the product of the cooling method -W. 2: These alarms do not occur on the product of the power specification '-20'.