ISE70_71-AB.eng Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm.
The dried air flows lo the outlet port, Exhaust Input Wet Air Fig, 4.11 Principle of the Adsorption Air Dryer Between 10-20% of the dry air passes through orifice 02 and column 2 in reverse direction to re-adsorb moisture trom the desiccant to rgenerate it, The dry air enters the saturated chamber and expands (dropping the temperature furthr, making the dry air ffectively even more dry to
This fitting is available in 27 different body styles, with connection sizes from M5 to + R(PT), and tube sizes from 4mm OD to 12 mm OD., FITTING, MALE ELBOW S/S, CONNECTORS, KG/KQ(X23) 1-TOUCH STAINLESS, FG, KQ(X23) 6MM, .05011 lb, Applicable tubing O.D. (mm)Connection threadsModel M5 type R type6R 1/4KGL06-02
Ground FG terminal advance. safety. Caution on operation Do not D o D o Warning Do not Do not Do not D o Do not Do not D o Warning : Operator error could result in serious injury SMC Corporation This product aims at application for common factory automation equipment.
Ground FG terminal advance. safety. Caution on operation Do not Do not Do not Do not Warning D o Do not Do not D o D o D o SMC Corporation This product aims at application for common factory automation equipment. Do not use LZC for machinery and devices (1) that directly concern human life or those which malfunction or failure could cause serious damage.
Rod O.D.Applicable tubing O.D. 10 20 25 30 M5 standard 01 standard 02 standard 03 standard 04-04 06-06 08-08 10-10 4 4 6 6 8 8 10 10 wBring up the body, while holding it down. w eTake the finger off the release ring and remove the speed controller from the One-touch fitting.
Size: 1 (Body Ported), Pilot: 0 (Internal Pilot), Power Source, Command Signal: 1 (24V, 0~10V), Port Size: 02 (1/4), Thread: Rc, Option: FG (Foot, Pressure Gauge)
Dimensions: In-line Motor LEY32: NM1 LEY25: NM1, NM2 2 x FA thread depth FB FD depth FE Motor flange Motor Motor flange Motor FD depth FE FH FC FC 2 x FA through (depth FB) (FG) FC FF FH FF (FG) FC FE LEY32: NM2 FD depth FE 2 x FA thread depth FB Motor flange Motor FC (FG) FC FF Dimensions [mm] Size Motor type FA FB FC FD FE FF FG FH NZ, NX M4 x 0.7 7.5 46 30 3.7 47 45 NY M3 x 0.5 6 45 30
Even if a noise filter is attached to a non CE marked products, the products cannot be changed to a CE compliant product. 1129 Series E-MY2C Dimensions: Remote Control Type (Remote controller unit) Controller Encoder cable on controller side (4 wires) Motor cable on controller side (6 wires) Noise filter Note 3) 200 or less To actuator Power supply cable (2 wires) 87.1 FG terminal M3 6.5
Symbol Symbol Terminating resistance FG FG FG FG Connector Connector Connector shell shell shell 220 1/2W + + + + 1 1 1 2 2 2 SG SG SG SG 5 5 5 Internal connection Internal connection Internal connection Pin No. Symbol Pin No. Symbol Pin No.
If connecting with GND, All I/O signal lines are not isolated from FG. 28 Doc.No.IZ-OMK0015D 4. Specifications 4-1.
Master unit Remote unit Local unit (Blue) (White) (Yellow) DB DG SLD FG Terminal resister DA Terminal resister DA DA Communication connector for CC-Link DB DG SLD FG DB DG SLD FG CC-Link dedicated cable CC-Link dedicated cable Drawing 2 Connect the terminal resistor between "DA-DB" (Refer to Drawing 3). Terminating resistor Drawing 4 NOTE 1.
FF FG FF FC Attachment mounting thread FE thread depth FH FC FG FF FA FB With adjuster With scraper Hexagon width across flats RB 2-M5 x 0.8 Supply port RA Stroke adjuster SA Hexagon width across flats RC RD SC At the maximum stroke RE Arrangement range RF SB Maximum adjustment dimension RJ Note) Observe the specified adjustment range when adjusting with a stroke adjuster.
FF FG FF FC Attachment mounting thread FE thread depth FH FC FG FF FA FB With adjuster With scraper Hexagon width across flats RB 2-M5 x 0.8 Supply port RA Stroke adjuster SA Hexagon width across flats RC RD SC At the maximum stroke RE Arrangement range RF SB Maximum adjustment dimension RJ Note) Observe the specified adjustment range when adjusting with a stroke adjuster.
Size: 1 (Body Ported), Operation: 0 (Air Operated Style), Port Size: 01 (1/8), Thread: N (NPT)
Size: 1 (Body Ported), Operation: 0 (Air Operated Style), Port Size: 02 (1/4), Thread: T (NPTF)
Size: 1 (Body Ported), Operation: 0 (Air Operated Style), Port Size: 02 (1/4), Thread: F (G(PF))
Size: 1 (Body Ported), Operation: 0 (Air Operated Style), Port Size: 02 (1/4), Thread: N (NPT)
Size: 1 (Body Ported), Operation: 0 (Air Operated Style), Port Size: 01 (1/8), Thread: T (NPTF)
Size: 1 (Body Ported), Operation: 0 (Air Operated Style), Port Size: 01 (1/8)