<br>Refer to the excerpt about the double knuckle joint from the “Dimensions of Accessories” page below. <br>A knuckle pin and retaining rings are included. <br>The CG1 series catalog can be found here.<br><br>
<br>Contact your nearest SMC sales representative for details. <br>The sensor part in particular needs to be protected by a cover, etc., if the product may be exposed to liquids in the operating environment.
<br>The corresponding mass is also called the corresponding mass of the impacting object. <br>① (Unit of collision speed v: m/s) Me becomes larger when the speed becomes less than 1 m/s because the square of the speed is the denominator.
<br>② The piping from the cylinder to the air-hydro converter should have an upward slope. <br>③ Do not position the port facing vertically downward. <br>④ Keep the piping as short as possible with minimal bending. <br>Note 1) When used as a single-side hydro unit, air may be mixed in with the operating oil.
<br>② The plate thickness has been optimized. <br>③ The guide rod length has been optimized.
<br>They are not related to the auto switch model. <br>Note 1) For solid state auto switches, the 2 numbers indicate the year and month of production, and the following 3 letters indicate the production lot.<br>Note 2) The letters may or may not have a rectangle around them.<br>Note 3) The production lot of reed auto switches is indicated in numbers instead of letters.
<br>The lead wire specifications of each auto switch can be found in the web catalog as shown below. Refer to each catalog for further details. <br>Note) The D-M9□ series uses flexible cables as standard.<br>The D-□ series catalog can be found here.<br><br>
<br>1 angle adjuster unit is required for retrofitting to an actuator without an auto switch unit.<br>When retrofitting to an actuator with an auto switch unit, 1 angle adjuster unit and 1 joint unit are required.<br>Sizes 20, 30, and 40 of the new CRB series released in November 2018 can be adjusted by ±5° on 1 side (start or end point) as standard.
<br>For the CRB2BWU(10-40)-180S, the angle can only be adjusted from 0° to 175°, just slightly under 180°. Therefore, selection of the type with a 270° rotating angle is required.<br><br>
<br><br>Refer to the rotary unit operation manual, which can be found here.
<br>The double vane type has double the pressure receiving area, so the torque is twice that of the single vane type.<br>However, due to the construction, only 90° and 100° rotating angles are possible.<br>The vane shafts of sizes 10, 15, and 20 of the CRB2 series are made of stainless steel for the single vane type and chrome molybdenum steel for the double vane type.
<br>The alarm contents and alarm codes can be checked in the controller setting kit.<br>However, only the alarm contents are displayed in the teaching box.<br>For more information, refer to the “Alarm details” section in the JXC51/61 series operation manual.<br>The JXC51/61 series operation manual can be found here.
LECP series: 40W<br>JXC*1: 40W<br>JXC*H: 55W<br>JXC*F: 40W<br>Note) The value is uniform regardless of the actuator used.<br>Note) This is a guideline for distribution panel design.
<br>The “D” indicates the body ported type. And the “B” indicates the box type.<br>Note) For the initial ZH series box type, the identification was printed onto the resin body.<br><br>
<br>
<br>For details on the part number and dimensions, refer to “Optional Accessories” in the IDF series catalog.<br>The old IDF6D/8D/11C/15C series catalogs can be found here.<br>And the IDF6E/8E/11E/15E series catalogs can be found https://www.smcpneumatics.com/Part-Builder-Links_ep_2458-1.html?https://smccatalog.partbuilder.smcpneumatics.com/support/faq/en-jp/?ca_id=air-dryers&fa_id=11170
<br>There is also a drain guide 1/4 female thread (option “J”) available for drain port piping. However, a ball valve, etc., will be required separately because this option does not have a valve function.<br><br>
<br>As steam is a gas, it cannot be removed by filtering. Various types of air dryers are required to dehumidify the air.<br><br>
<br><br>Note 1) Even for regulators with a relief mechanism, there is a slight difference between the relief start pressure and the set pressure.<br>Note 2) The relief function lowers the pressure to the set value by releasing the outlet pressure from the relief hole in the center of the diaphragm to the atmosphere when the outlet pressure becomes higher than the set pressure.
<br>Therefore, it is necessary to consider, for example, changing the body size.<br>Note that the flow rate characteristics also change depending on the pressure conditions on the inlet side.<br>(A 316 stainless steel regulator with a Rc3/4 or Rc1 port size is also available as a special order.)<br><br>