<br>Note 1) The element of the old AF and AW series (4 digits: AF□□□□), which were released in 1985, was initially a bronze element and then became a nonwoven fabric element later on. <br>Products with the bronze element need to be replaced with the current product.
<br>For the AV2000-A: 1<br>For the AV3000-A: 4<br>For the AV4000-A: 7<br>For the AV5000-A: 10
<br>The part numbers of standard AR20 to AR60 round type pressure gauges are “G36-10-01” and “G46-10-01”(for the R thread type). <br>For example, the part number of the AR30-03BG-A pressure gauge is “G36-10-01.” <br>Details on the round type pressure gauge (with color zones) can be found https://www.smcpneumatics.com/Part-Builder-Links_ep_2458-1.html?https://smccatalog.partbuilder.smcpneumatics.com/support/faq/en-jp/?ca_id=combination-units&fa_id=10974
<br>④ The pipe length from the strainer to the liquid collector body is 20 m or more when the mounting height of the liquid collector is 3 m or more for a water-soluble solution or 1 m or more for an insoluble solution. <br>⑤ The dynamic viscosity of the fluid is too high to flow. <br>⑥ The operating fluid is air. (Air cannot be used as the fluid.
<br>Classification of a Class 2 pressure vessels is as follows.<br>① The internal capacity exceeds 40 L.<br>② The internal size exceeds 200 mm and the length exceeds 1000 mm.<br>③ The container holds gas with an operating pressure of 0.2 MPa or more.<br><br>Ref.) The capacity of the VBAT series air tank does not exceed 40 L.
<br>
<br>Note) The KK□ series S coupler cannot be used as a stop valve that requires zero leakage. Due to the specifications of the product, a certain amount of leakage is unavoidable.<br><br>
<br>Note 3) If the surge pressure is higher than the max. operating pressure, it may cause damage to the fitting or tube.<br><br>
<br><br>Meter-in control is a control method in which the speed of the cylinder is controlled using the cylinder supply flow rate.<br>With meter-in control, the exhaust conditions do not affect operation, and the piston can start moving quickly. (Cylinder lurching can be prevented.)
<br>Note) The accuracy will decline if IN side piping deviating from the recommended straight piping length or bore size is used.<br><br>
<br>The VX3 series catalog can be found here.<br><br>
<br>Be sure to check the specifications and precautions listed in the catalog of each type of tubing and fitting. <br>Note that LQ series piping requires a special tool. <br><br>
<br><br>Fittings and tubing catalogs can be found here.
Further details on the PA/PAP/PAX series can be found <br>In this case, use the bypass piping set (optional accessory) to secure the flow rate. <br>Note) The temperature stability is as follows: ±2.0℃ for the HRSE, ±0.5℃ for the HRS090, and ±1.0℃ HRS100/150/200.<br><br>
<br>First, refer to the “Transport and Setting Up” section in the HRS series operation manual. <br>Wiring examples are shown in the “Wiring of remote operation signal input” and “Wiring of run/stop signal input・Remote signal input” sections. <br>Next, to enable remote signal input, change the communication mode from “LOCAL” to “DIO” mode.
<br>Please check the figure below. If the product is equipped with a control power supply, this control power supply circuit is provided. <br>If the operating power supply voltage is energized while the valve is open, it is acceptable not to drop it to the holding voltage.<br><br>
<br><br>・While it is possible to mount a G36-10-01 or G46-10-01 pressure gauge on a VEX113□/123□ series regulator, it will be larger than the width of the product body.<br>・It is also possible to mount a G46-10-01 pressure gauge on a VEX133 □ series regulator so long as it does not interfere with the piping.
<br>Note) The all side piping option was only added to the VH200 series (as described in ②) in 2016. The VH series catalog can be found here<br><br>