0.55

Possible to use in vacuum applications Up to 100 kPa Non-locking push type Push-turn locking slotted type Push-turn locking lever type Manual override Pilot exhaust type Lubrication Mounting orientation Impact/Vibration resistance (m/s2) Note) Individual exhaust Not required Unrestricted 300/50 Dust-tight (IP65 for D, Y, T) Series VP300 Enclosure Note) Impact resistance: No malfunction occurred

Vacuum Unit Ejector / Vacuum Pump System

switch) 150m/s2 (Without pressure sensor and pressure switch, With pressure sensor) Impact resistance Note 2,3) 100m/s2 (With pressure switch) Standard CE, RoHS Note 1) The characteristics are satisfied when tested for 2 hours in each of the X, Y and Z directions at 10 to 500 Hz without energization.

Low Differential Pressure Sensor

Do not drop, bump, or apply excessive impact (100 m/s2) while handling. Although the body of the controller case may not be damaged, the inside of the controller could be damaged and cause malfunction. 2. The tensile strength of the power supply/output connection cable is 50 N; that of the pressure sensor lead wire with connector is 25 N.

PSE550/300

Do not drop, bump, or apply excessive impact (100 m/s2) while handling. Although the body of the controller case may not be damaged, the inside of the controller could be damaged and cause malfunction. 2. The tensile strength of the power supply/output connection cable is 50 N; that of the pressure sensor lead wire with connector is 25 N.

Compact Cylinder

Auto Switches Common Specifications Type Reed auto switch Solid state auto switch 1 ms or less 1.2 ms Operating time 300 m/s2 1000 m/s2 Impact resistance 50 M or more at 500 VDC Mega (Between lead wire and case) Insulation resistance 1500 VAC for 1 minute (Between lead wire and case) 1000 VAC for 1 minute (Between lead wire and case) Withstand voltage 10 to 60C Ambient temperature IEC60529

CE

When excessive impact (300m/s2 or more) is applied to a reed switch during operation, the contact point will malfunction and generate or cut off a signal momentarily (1ms or less). Consult SMC regarding the need to use a solid state switch depending upon the environment. 7. Do not use in an area where surges are generated.

A

Standard G Centralized Piping Type 1001~ 3000 +2.8 Port Size Front/side M5x0.8 M5 x0.8 Rc(PT)1/8 Rc(PT)1/8 Rc(PT)1/4 Rc(PT)3/8 Rc(PT)3/8 Bottom (centralized) 4 4 5 6 8 10 11 The Operating Speed must not exceed 1000mm/s when air cushion alone is used.

3 Port Solenoid Valve Rubber Seal Series SY100 1

Lead wire length 2000 mm Cover Concave Pin Nil 6 10 15 20 25 30 50 300 mm 600 mm 1000 mm 1500 mm 2000 mm 2500 mm 3000 mm 5000 mm Lever DC indicator Socket Part no.

V100

Lead wire length 2000 mm -+ Socket Nil 6 10 15 20 25 30 50 300 mm 600 mm 1000 mm 1500 mm 2000 mm 2500 mm 3000 mm 5000 mm Lead wire Connector Hook For DC V114-5LO SY100-30-4A-20 For AC V114A-1LO SY100-30-1A-20 2.

3 Port Solenoid Valve Rubber Seal Series SY100

Lead wire length 2000 mm Cover Concave Pin Nil 6 10 15 20 25 30 50 300 mm 600 mm 1000 mm 1500 mm 2000 mm 2500 mm 3000 mm 5000 mm Lever DC indicator Socket Part no.

Pallet Lock Cylinder W-R1/W-R3 Series

Specications Clamping Force W-R1-S2Type Type 1 Type 3 Mass of transferred object 1000 kg or less 3000 kg or less 5000 Possible amount of positional correction 50 mm or less 4000 Clamping force 4430 N 4070 N Clamping force [N] Operating time 1.0 s or more 0.8 s or more 3000 Cylinder operation stroke 83.5 mm 140 mm Bore size 100 mm 2000 Cylinder proof pressure 1 MPa Max. operating pressure

Solid-state Auto Switches for Direct Mounting Series D-M9N(V)/D-M9P(V)/D-M9B(V)

)(5000) 8 2 3.2 4.6 2.7 2.8 4 22 500(3000) 4 Most sensitive position 6 2.8 20 2.7 3.2 6 Most sensitive position 22 500(3000) 2.6 9.5 4 Specific Product Precautions Be sure to read before handling.

IZx-OMT0049

Handling Caution 1) Do not apply excessive external force or shock (100m/s2 or more) to the product Even if the there are no problems with the appearance of the controller, high voltage power supply module or bar, the damage of the internal components may cause malfunction. 2) When the bar length exceeds 820mm, hold the both ends and the middle of the bar so that moment load is not applied

Direct Operated Pilot Operated 2-Port Solenoid Valve Refer to pages 7, 9, 11, 25, 35, and 39 for details.

Critical pressure 0.6 0.5 Sonic 0.5 0.4 0.4 0.3 0.3 0.2 0.2 0.1 0.1 JSXD30 Port size 1/4 JSXD30 Port sizes 3/8, 1/2 JSXD40 Port size 3/8 JSXD40 Port size 1/2 JSXD50 Port size 3/4 JSXD60 Port size 1 10 1000 2000 3000 10 1000 2000 3000 4000 15 2000 4000 6000 8000 15 2500 5000 7500 10 20 5000 10 15000 25 5000 10 15000 20 Flow rate Q [L/min (ANR)] For Air (Orifice diameter: 35 mm, 40 mm, 50 mm

HRL

Altitude [m] q Upper limit of ambient temperature [C] w Cooling capacity coefficient Less than 1000 m 45 1.00 Less than 1500 m 42 0.85 Less than 2000 m 38 0.80 Less than 2500 m 35 0.75 Less than 3000 m 32 0.70 Read the operation manual completely before operation, and keep this manual where it can be referred to as necessary. 14) In locations where strong impacts or vibrations occur 15)

Power Clamp Cylinder

Wiring Diagram Black S1 Lood Blue () 4 3 S2 Lood 1 2 (+) Brown White Note) Both TURCK and P&F are common. 193 Series CKZT Caution 1. When mounted vertically, the maximum opening angle is different from the standard specifications. The opening angle is different from standard specifications depending on the arm offset, bore size and clamp arm. Refer to the following for details.

Rotary Clamp Cylinders

When excessive impact (300 m/s2 or more) is applied to a reed switch during operation, the contact point will malfunction and generate or cut off a signal momentarily (1 ms or less). Consult SMC regarding the need to use a solid state switch depending upon the environment. 7. Do not use in an area where surges are generated.

ZL3-OM00601

m/s2) *3 100 *1: Values are based on standard of SMC measurements.

Nozzle Type Ionizer

Do not drop, hit or apply excessive shock (100 m/s2 or more) to the product when handling it. Even if the product appears undamaged, the internal components may be damaged, leading to a malfunction. 2. When mounting/dismounting the cable, use your finger to pinch the claw of the connector, then attach/detach it correctly.

Rubber seal Series 10-SYJ3000/5000/7000 4/5 port solenoid valve

How to mount on the same manifold is shown on the following pages. 10-SYJ3000, 10-SYJ300 Page 507 10-SYJ5000, 10-SYJ500 Page 529 10-SYJ7000, 10-SYJ700 Page 550 If 4 or 5 port valve is used as a 3 port valve Series 10-SY 3000/5000/7000 may be used as a N.C. or N.O. 3 port valve by plugging one of the A, B ports. Be sure not to plug the exhaust ports (R).