Air Cylinder NCA1 Series Bore Piston Area Forces (lbs); Push Stroke (in) (in) Operating medium Pressure (PSI) 50 60 80 100 200 250 1.5 1.767 88 106 141 177 353 442 HOW TO USE THIS TABLE 1 Locate column with desired operating pressure. 2 Move down that column and locate the thrust value which is equal (or the next larger to the force to be delivered by the cylinder.) 3 On that same line, locate in the first (left)
It can operate in temperatures between 10 to 60C if there is no risk of the moisture in the air freezing.
Brown [Red] When two switches are connected in series, a load may malfunction because the load voltage will decline when in the ON state. The indicator lights will light up if both of the switches are in the ON state.
Specifications The conventional pneumatic pressure line AM Series + AMD Series have been integrated to achieve a reduction in installation space, savings in piping installation labor, and reduced costs.
It is already built-in to the rectifier circuit. For R and U, DC voltage is only available. Power saving circuit is only available in the "Z" type.
Product with Nuts How to order a flow sensor, PF2D5S series, etc. nut type fittings without a nut (including insert bushings) in one place.
SUP srG srG SUP Incresing Signal Conatanl signal Decreasing Signal 2 CYLINDER POSITIONING ASSEMBLY HOW TO ORDER HOW TO ORDER The part number key below will assist in ordering. substitute the required bofe, stroke, etc., in the key example to conslruct the number ol the required actuator.
Mounting of Auto Switch When mounting an auto switch, insert it into the cylinder's switch groove from the direction shown in the figure below. After setting it in the mounting position, use a flat head watchmakers screwdriver to secure it with the mounting screw which is included.
Also suited for use in areas in which water splashes, such as food processing equipment or car washers. q Do not operate the cushion valve in the fully closed or fully opened state. Using it in the fully closed state will cause the cushion seal to be damaged.
When using another switch in addition, list its part number next.
It can be used in the vacuum (up to 100 kPa) or low pressure line with 0.15 MPa or less.
Olf a lubricant is used in the system, use turbine oil type f 1 (lSO VG32). lf lubricant has been used in the system, do not cease to lubricate as the original lubricant applied during manutacturing will have been washed away.
Removes odor and gas ingredients in compressed air.
magnets Cushion In the case of cylinders with built-in magnets but no auto switches, do not indicate any auto switch type symbol.
(In case of output OUT2, n_1, 2 to be n_3, 4 and P_1, 2 to be P_3, 4.) Note 6) The display unit conforms to the CE mark.
Olf a lubricant is used in the system, use turbine oil type f 1 (lSO VG32). lf lubricant has been used in the system, do not cease to lubricate as the original lubricant applied during manutacturing will have been washed away.
(Valve in the initial stage.) Vibration resistance: No malfunction occurred in a one-sweep test between 8.3 and 2000Hz. Test was performed at both energized and de-energized states to the axis and right angle directions of the main valve and armature. (Value in the initial stage.) VNl VQ 1 (P) N.C. Note 5) DIN connector style: Applicable to dust and jet proof (IP65).
Order Made 2 With IN-OUT Flange 1 With Pressure Differential Gauge (GD40-2-01) A pressure differential gauge can be installed in the body to check the life of filter element. It allows for easier piping and compact size. For easier flange piping.
Air Flow Select the model in accordance with the following procedure taking the inlet pressure and max. air flow into consideration. (Example) Inlet pressure: 0.6 MPa Max. air flow capacity: 5 m 3/min (ANR) 1. Select the point of contact A of inlet pressure and max. air capacity in the graph. 2.