Series PF2D Digital Flow Switch For Deionized Water and Chemicals (In case of output OUT2, n_1, 2 to be n_3, 4 and P_1, 2 to be P_3, 4.) Note 6) The display unit conforms to the CE mark.
Olf a lubricant is used in the system, use turbine oil type f 1 (lSO VG32). lf lubricant has been used in the system, do not cease to lubricate as the original lubricant applied during manutacturing will have been washed away.
(Valve in the initial stage.) Vibration resistance: No malfunction occurred in a one-sweep test between 8.3 and 2000Hz. Test was performed at both energized and de-energized states to the axis and right angle directions of the main valve and armature. (Value in the initial stage.) VNl VQ 1 (P) N.C. Note 5) DIN connector style: Applicable to dust and jet proof (IP65).
Order Made 2 With IN-OUT Flange 1 With Pressure Differential Gauge (GD40-2-01) A pressure differential gauge can be installed in the body to check the life of filter element. It allows for easier piping and compact size. For easier flange piping.
Air Flow Select the model in accordance with the following procedure taking the inlet pressure and max. air flow into consideration. (Example) Inlet pressure: 0.6 MPa Max. air flow capacity: 5 m 3/min (ANR) 1. Select the point of contact A of inlet pressure and max. air capacity in the graph. 2.
Flow switch WARNING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. Danger: For the integrated display type, it displays flow rate, set value and errors.
Air Flow Model Selection Select the model in accordance with the following procedure taking the inlet pressure and max. air flow into consideration. (Example) Inlet pressure: 0.6 MPa Maximum air flow rate: 5 m 3/min (ANR) 1. Select the point of contact A of inlet pressure and max. air capacity in the graph. 2.
Refrigerated Air dryer Series IDU/IDF In compliance with the Montreal Protocol Regulations, P/A uses refrigerants R134a and R407C in its refrigerated air dryers to prevent any damage to the earth's ozone layer.
Air Flow Max. flow line AT Select the model in accordance with the following procedure taking the inlet pressure and max. air flow into consideration. (Example) Inlet pressure: 0.6 MPa Max. air flow capacity: 5 m3/min (ANR) 1. Select the point of contact A of inlet pressure and max. air capacity in the graph. 2.
Air Flow Max. flow line Model Selection Select the model in accordance with the following procedure taking the inlet pressure and max. air flow into consideration. (Example) Inlet pressure: 0.6 MPa Max. air flow capacity: 5 m3/min (ANR) 1. Select the point of contact A of inlet pressure and max. air capacity in the graph. 2.
Install the aftercooler in a location that facilitates maintenance and inspection. 3. Install the aftercooler in a location with minimal vibrations. 4. Ventilate the area because the surrounding temperature increases due to the exhaust heat from the aftercooler. 5. The air cooled type aftercooler cannot be used in a location in which the temperature exceeds 50C.
The test were performed one time each in the axial and right angle directions of the main valve and armature, in both energized and de-energized states (Valve in the initial stage). Vibration resistance: No malfunction occurred in a one-sweep test between 8.3 and 2000Hz.
F R L T B 1 R Axial entry Right entry 200/230VAC (50/60Hz) 2 Y 0 Without motor Bottom entry Specifications Intermediate strokes 100 5.1 200 5.9 300 6.7 400 7.4 500 8.2 5 to 40 (with no condensation) 10 225 400 mm kg C kg N mm/s mm Standard stroke Strokes other than the standard strokes on the left are available by special order. Consult P/A.
Note 2) Impact resistance: No malfunction when tested with a drop tester in the axial direction and at right angles to the main valve and armature, one time each in both an energized and deenergized state.
However, a oreat deal of force will be needed to manually op6ration this valve in order to over@methe mechanical spring as well as the air pressure assisting the spring.
When in the exhaust position, the valve may be padlock secured, preventing accidental start-ups while personnel are cleaning or servicing equipment. The supply/exhaust status of the air flow can be verified at a glance in the indicating window.
Port size Dimensions Dimensions A Connection HA B IN OUT AT IN OUT ID A B AMG AFF AM Drain Misc.
The dither may generate vibrations in fe valve which produces a growling noise and may be ad.iusted within a range of 100 to 2m Hz by luming the DITHER adiustment screw.
Use ot a protective cover is guggested when installed in a olace where water or oil will splash momentarily. 3. When installed in a dusty place, please install a silencer on the exhaust port. Of Fluid Remarks 1. Fittration to 5 microns is sutficient lor operation. 2. large quantity ot drainage causes incorrect operation of pneumatic products as well as envionmental contamination.
The meter-out type is electroless nickel plated, while the meter-in type is black zinc chromate plated.