Speed Controller with One-touch Fitting ASD Body size Port size M5 M5 x 0.8 U10/32 10-32UNF 1 M5 x 0.8 10-32UNF AS AS-FE 2 F A 1 AS 1 M5 06 0 E Body size 1 KE AS-FG F A 1 AS 2 01 06 2 0 S Body size 2/3/4 AS-FP AS-FM Body size Made to Order Refer to page 562 for details.
As a rule, after the rod bottoms out, back off 1 to 2 turns.
As a rule, after the rod bottoms out, back off 1 to 2 turns.
Series SV used as a 3 port valve Caution Using a 5 port valve as a 3 port valve Series SV valves can be used as normally closed (N.C.) or normally open (N.O.) 3 port valves by closing one of the cylinder ports (A or B) with a plug. However, they should be used with the exhaust ports kept open. They are convenient at times when a double solenoid type 3 port valve is required.
For installation and removal, use an appropriate pair of pliers (tool for installing a type C snap ring). 2. Even if a proper plier (tool for installing type C snap ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a snap ring may be flown out of the tip of a plier (tool for installing a type C snap ring).
Note 2) When ordering the limit switch base and the dog bracket individually, a spring washer for the mounting bolt (hexagon socket head cap screw) will be attached as a standard.
Connector Lead wire Socket Usage of SX3000/5000/7000 as a 3 Way Valve Caution Hook Insert a socket into square hole In the case of using a 5 port valve Series SX3000, 5000, 7000 may be used as and N.C. or N.O. 3 way valve by plugging one of the A, B ports. Be sure not to plug the exhaust ports. Can be used when a double solenoid, 3 way valve is required.
Uni-Threads Conventional Threads U N I T H R E A D R I D G E S H A P E A new ridge shape has been created as a Uni-Thread f o r c o m m o n a p p l i c a t i o n t o R c ( P T ) , G ( P F ) N P T, a n d NPTF female threads with different thread diameters, pitches, tapered angles, ridge shapes, etc..
Wiring should be kept as short as possible.
Using the cylinder as a shock absorber may cause damage.
A unit connected to a PLC to communicate input and output data. U U Side The side connected to the solenoid valve when the product is connected to a manifold. -10No.EX-OMX1011 Assembly Composing the unit as a manifold : If the unit was purchased as a manifold, the work described in this section is not necessary. (1) Connect the unit to the end plate.
9 Baking Gases such as oxygen and nitrogen, which have a small adsorption activation energy (E) and a short adsorption residence time (), are evacuated quickly.
Please do the following to prevent this problem: 1) Tubing from a solenoid valve to a cylinder should be as short as possible to assure the evacuation of the generated water vapor into the air.
the table below, should be considered as a coefficient determined in accordance with each stroke.
This operation could be hazardous to personnel, as their hands or feet could get caught by the clamp arm, or could lead to equipment damage. Therefore, it is important to secure as a danger zone a cylindrical area with the length of the clamp arm as its radius, and the stroke plus 20mm as its height.
the piston rod material will be treated as a special order.
As a guide, refer to the proper tightening torques shown below.
Can be used for a wide range of pressures from a low vacuum up to a pressure of 1 MPa The use of a special profile ensures sealing and reduces resistance when the tube is inserted.
of the cylinder ports (A or B) enables use as a normally closed (N.C.) or normally open (N.O.) 3 port valve.