CA2 C0.5 file chamfer R sphere TP R sphere H W1 T H H Symbol: A12 Symbol: A13 Symbol: A14 Symbol: A15 Symbol: A16 Symbol: A17 Symbol: A18 Symbol: A19 MM 30 MM 30 MM 30 H A H A H A MM 30 30 L RD C B A H A L K H W MM DA 30 MM DA 30 MM MM AL H LB K A AL H AL L K H L A H Symbol: A28 Symbol: A29 Symbol: A30 30 DA 30 30 MM L W MM W A L H AL A H A T T MM H 65 Series CA2 Made to Order Specifications
Manual Override How to Use L/M Plug Connector Caution Warning Attaching and detaching connectors Without an electric signal for the solenoid valve the manual override is used for switching the main valve. Locking type (Tool required) is available as an option.
Please contact SMC if an application under such conditions cannot be avoided.
A quick recovery time indicates little liquid pool. 50 Ratio of resistance [k m] Particle ratio [number/cc] 100 2 or 3 particles/cc 10 00 10 20 30 40 50 60 70 1 0 5 10 15 20 25 30 Duration of flow [min] Duration of flow [min] The data was obtained by performing an actual 10 minutes supersonic cleaning using an average 16 Mcm of deionized water at class 10 clean room (1 l/min flow rate).
Contact SMC if an inverter welder or a DC welder will be used.
(An assembly is shipped under the condition shown in the figure.)
7 Made to order common specifications 5.4-46 -XC11 Dual stroke cylinder/Single rod !8 5.4-52 -XC12 Tandem cylinder !
Hs T (mm) Symbol BX BY D F GA GB L M N S T W Wc Ws Z ZZ Hs IA K Bore size 40 56 54 16 44 77 10 55 M12 x 1.5 86 112.5 57 5 39 27.5 114 228 46 47 14 50 64 64 20 55 78.5 10 58 M16 x 1.5 87.5 117 60 7 41 33 118.5 232.5 50 58 17 63 74 74 20 69 82 12 58 M16 x 1.5 91 120.5 67 5.5 48 39 122 236 56 72 17 12 Series CLK1 Clamp Cylinder with Lock Accessory Dimensions (mm) Single Knuckle Joint Double
With an ejector When a few air cylinders are locally used.
Do not use in an atmosphere containing an inflammable gas or explosive gas. Use in such an atmosphere is likely to cause a fire or explosion. This system is not explosion-proof. Caution 1. Select the proper type of enclosure according to the environment of operation.
Mixed single and double wiring is available as an option. 1. How to order valves Indicate an option symbol, -K, for the manifold no. and be sure to specify the mounting position and number of stations of the single and double wiring by means of the manifold specification sheet. Refer to following model no. for inch-size One-touch fittings.
The flatness of the mounting surface may not be maintained, which would cause an increase in sliding resistance.
Rights Reserved No.PS-OMR0002-K
The control signal of an entire system can be managed by Fieldbus System.
The following graph shows an example of the detection of an overload warning when the overload warning level (Pn52B) is changed from 20% to 50%. An overload warning is detected in half of the time required to detect an overload alarm.
10, 15, 20, 30, 40 MRQ K J XA39 XA40 XA41 XA45 K K K XA46 Y Y Y Y Y 20, 30, 40 Y J K K, T K, T K 10, 15, 20, 30, 40 K K K K, T K Z X X, Z J J J, Z Z J 20, 30, 40 Z J 10, 15, 20, 30, 40 T J Reversed shaft, Change of double shaft length X 20, 30, 40 Reversed shaft, Change of double shaft length Combination Chart of Made to Order Chart 4.
Parameter Setting 46 I/O Map 46 Diagnostic 46 Accessories 46 Precautions before mounting 47 -2No.EX-OMN0038-C Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
Be careful to the supply pressure and kinetic energy when performing an intermediate stop. Fine end stroke adjustment is considered as an intermediate stop, so the considerations for an intermediate stop must be observed when making any fine adjustments. When stopping the external slider in an intermediate position with an external stopper.
[Tips]
for intermediate stop using an external stopper, etc.