MHL2-16Dl MHL2-20Dl MHL2-25Dl MHL2-32Dl MHL2-40Dl MHL2-10Dl @6 @7 Seal kit Note) NBR MHL10-PS MHL16-PS MHL20-PS MHL25-PS MHL32-PS MHL40-PS @8 @9 #0 Note) No. @6, @7, @8, @9, #0 are included. 2.2-5 Wide Opening Air Gripper Series MHL2 Setting Method of Auto Switch Auto Switch Hysteresis To set the auto switch, insert the auto switch into the switch groove of the air gripper from the direction
Bore size (mm) Double acting Single acting Double acting/ spring loaded RSG40D-PS RSG40B-PS RSG40T-PS RSG50D-PS 40 50 A set of the above Nos. 18, 19 & 20 RSG50B-PS RSG50T-PS Seal kits are sets consisting of items 18, 19 and 20, which can be ordered using the order number for each cylinder bore size. 17 Adjustable Mounting Height Type Series RSG Rod End Configuration Round Bar Type Basic
t Plug } IN OUT OUT IN q o q Plug y Purge air for dehumidification u Plug u Purge r Purge Purge air for dehumidification Component Parts Material Description No.
t signai VDC 1 2 3 Input signalVDC 1 2 3 Hysteresis r c 0.5 z o E ! 0 E E ,o5 5 E 1 2 3 4 lnplrl signal VDC lrpul signa VDC 1 2 3 lnput slgna!
t signai VDC 1 2 3 Input signalVDC 1 2 3 Hysteresis r c 0.5 z o E ! 0 E E ,o5 5 E 1 2 3 4 lnplrl signal VDC lrpul signa VDC 1 2 3 lnput slgna!
MHW25-PS MHW32-PS MHW40-PS MHW50-PS !
CA2Y80-PS Grease pack (10 g) 1 pc. CA2Y100-PS Accessory When only grease for maintenance is necessary, please order by the following part numbers.
Content Support brackets & side supports Connecting section Tube Body Wear ring Piston seal Configuration End units End unit Tube Body Oil felt seal Support bracket End unit Cylinder tube Spare parts Bore size MF PS Model Bore size T 3-dimensional transfer Spare parts MFP Bore size G Bore size MF MFT Optional parts MF-S32 (side support ) Body A B A B 3-dimensional transfer: Single units
AC 110 12 2 12 3 q e w e t y 220 10 1 10 1.5 440 6 1 3 1 550 5 0.8 2 0.5 r b contact w a contact r q DC 24 3 2.5 3 2.5 C C 48 1.5 1.2 1.5 1.25 When rising pressure q w = ON e r = OFF When rising pressure q e r y = ON q w r t = OFF 110 0.5 0.25 0.5 0.2 220 0.25 0.1 0.25 0.1 Insulation resistance: 100 M or more at 500 VDC by megameter Voltage resistance: 2000 VAC/1 min. 16-9-5 2 Series
CK1A40-PS 40 Component Parts No. Description Material Qty Note No.
Cable, connector, hub, please use the one that satisfies the standards of IEEE802.3 10BASE-T / 100BASE-TX. User's equipment can be connected up to four at the same time.
Note Main parts 16, 17, 18, 19 MHC6-PS Seal kit MHCA2-6 (Short body) Double acting/with fingers closed Single acting Double acting/with fingers open o i e q t !1 !6 w !0 r !4 u !5 !7 y !3 !2 Parts list No. Description Parts list No.
Table 4 20 25 32 40 Rod seal CM20Z-PS CM25Z-PS CM32Z-PS CM40Z-PS The rod seal is not delivered in sealed packaging for storage independently, so it must be used within 1 year.
9 NBR MHC10-PS MHC16-PS MHC20-PS MHC25-PS Seal kit @0 @1 2.6-5
Note 2) 20 25 CM2X20-PS Rear trunnion type (1 pc.) Note 2) Rod seal: 1 pc. CM2X25-PS 32 40 Boss-cut basic type (1 pc.) CM2X32-PS Grease pack (10g): 1 pc. Boss-cut flange type (1 pc.) CM2X40-PS Boss-cut trunnion type (1 pc.) 2. Grease packs When maintenance requires only grease, use the following part numbers to order.
1 Air Checker: Electronic Pressure Switch Series PS1000/PS1100 For Positive Pressure For Vacuum ZSE ISE PSE For General Pneumatics Z I SE3 PS Z I SE1 2 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com ZSP ISA2 IS ZSM PF2 IF Data Small, lightweight electronic pressure
PS Automatic fluid-fill port Circulating fluid return port TS TS Temp. sensor (Ref. suction Temp. sensor (Return) Compressor DC inverter compressor Customer's machine (Heat load) Level switch Refrigerating circuit Tank drain port PS TS Circulating fluid outlet port Press.. sensor Temp. sensor (Outlet) (Outlet) Fig. 8-2: Flow Diagram 8.3 Flow Diagram HRS Series 8-4 HRX-OM-W032 Chapter 8 Documents
S Y M B O L S S H O W T H E F U N C T I O N O F A C O M P O N E N T B U T D O N O T I N D I C A T E T H E C O N S T R U C T I O N .
S Y M B O L S S H O W T H E F U N C T I O N O F A C O M P O N E N T B U T D O N O T I N D I C A T E T H E C O N S T R U C T I O N .
E R I E S P S 1 0 0 0 / 1 1 0 0 L PS 00 L Grommet and Lead Wire 3m W I R I N G M E T H O D P I P I N G M E T H O D RO6 6 Reducer R07 1/4 Reducer S W I T C H S P E C I F I C AT I O N 10 2-Wire System (for Positive Pressure) 11 2-Wire System (for Vacuum and Residual Pressure) D I M E N S I O N S PS1000/1100 S W I T C H O U T P U T F U N C T I O N Courtesy of Steven Engineering, Inc. !