Series IDG When very clean air is required, install a separator as mentioned above on the downstream side, or instead of a regulator, use the order made specification (refer to page 35) fitted with a micro mist separator regulator (series AWD). 3.
10 A 180/200 W 50/60 Hz 220 W 0.01 m (99.9% filtration efficiency) Particles of 0.3 m or more: 3.5 particles/L [ANR] or less Heater operation, PID control Singlephase 200 VAC (50/60 Hz) 2.1 A 5 A Singlephase 230 VAC (50/60 Hz) 2.1 A 5 A Singlephase 100 VAC (50/60 Hz) 9.4 A 15 A Singlephase 200 VAC (50/60 Hz) 4.8 A 10 A Singlephase 230 VAC (50/60 Hz) 4.8 A 10 A Power supply Note 4) Operating
To use a perfect valve and a spacer style regulator, use a manifold or a sub plate as the standard and stack in the following order: the perfect spacer, spacer style regulator, and the valve.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
To release residual pressure, select a model with a back flow mechanism.
[Check valve] A check valve is a safety device intended to prevent reverse flow. The AP 64 is a unique design with only one moving part in the gas stream, an O-ring. It is a springless design, free of springs and poppets. [Vacuum generator] A venturi device that creates vacuum by flowing gas through a nozzle.
When a surge generating a load such as a relay or solenoid is directly driven, use a type of switch with a built-in surge absorbing element. 4. Since the type of fluid varies depending on the product, be sure to verify the specifications. The switches do not have an explosion proof rating. To prevent a possible fire hazard, do not use with flammable gases or fluids. 5.
To release residual pressure, select a model with a back flow mechanism.
Can be used when a double solenoid,3 way valve is requiled Prrq e*'tg4 9 PPorf A Port ' N o i (X) plus B A I dfNll= r / r / r \ r l R P R (x) ptus B A ff-7TrTl utrt / | \ ltrl l l / r l r \ t l R P R Leakage Voltage _q cll 6 Note that when using resistor in parallel with a contact, the leakage voltage may increase due to the leakage current flo\{ing through the resistor (!
Can be used when a double solenoid,3 way valve is requiled Prrq e*'tg4 9 PPorf A Port ' N o i (X) plus B A I dfNll= r / r / r \ r l R P R (x) ptus B A ff-7TrTl utrt / | \ ltrl l l / r l r \ t l R P R Leakage Voltage _q cll 6 Note that when using resistor in parallel with a contact, the leakage voltage may increase due to the leakage current flo\{ing through the resistor (!
Width: Max. 62% reduction (in comparison with SMC CA2 cylinder) Bottom mounting Side mounting Axial mounting (mm) A Dimension Comparison A Size Reduction rate MU CA2 24 28 32 39 50 60% 60% 62% 62% 57% 25 32 40 50 63 60 70 85 102 116 A (MU) A (CA2) Various brackets are available to accommodate a wide range of applications. Can be mounted with short pitch.
A CAT.ES100-43 A For General Fluids High Precision Digital Pressure Switch F/ISE ZSE 50 60 50 60 Series High precision/High resolution pressure switch. Applicable for pressure detection with a wide range of fluids, by using a stainless steel diaphragm. Pressure detection for a wide range of fluids.
A slit panel and a panel without slit are used in combination. Refer to the operation manual for details.
Do not use a load that generates surge voltage.
(Figure 1) The cylinder should be operated using a connection method which allows for assimilation of shaft alignment variations and deflection due to the cylinder's own weight. A drawing of a recommended mounting is shown in Figure 2. 7. Careful alignment is necessary when connecting to a load having an external guide mechanism.
watch maker's screwdriver with a grip diameter of 5 to 6mm.
B 5(3) 5(3) 6(4) 11 A 6(4) 6(4) 7(5) 12 B 0(0) 0(0) 0.5(0) 5.5 A 0.5(0) 0.5(0) 1.5(0) 6.5 B 3(1) 3(1) 4(2) 9 A 4(2) 4(2) 5(3) 10 Hs 69.5 72 75.5 79.5 B 6(4) 6(4) 7(5) 12 Hs 60 62.5 66 70 A 7(5) 7(5) 8(6) 13 Hs 25 27.5 31 35 B 0(0) 0(0) 1(0) 6 Hs 22.5 25 28.5 32.5 A 1(0) 1(0) 2(0) 7 B A B 1.5(0) 1.5(0) 4.5(2.5) 3.5(1.5) 2.5(0.5) 4.5(2.5) 3.5(1.5) 2.5(0.5) 5.5(3.5) 10.5 4.5(2.5) 9.5 3.5(1.5
However, if there is any problem, use a 3 wire DC style. 3.8-11 Series CXT Auto Switch Mounting Position and Mounting Height Reed switch Solid state switch A B W D-F9NW D-F9PW D-F9BW D-A90 D-A93 D-A96 D-F9N D-F9P D-F9B D-F9BAL 12 A B W 16, 20, 25 W A B 32, 40 (mm) D-A90 D-A93 D-A96 D-F9NW D-F9PW D-F9BW D-F9N D-F9P D-F9B Auto switch model D-F9BAL Symbol A B W A B W A B W Standard stroke 12
t r r , " . . a : r i . . . , r i a , r . .