PFxx-OMY0005 OUT2 17 OUT output bit Accumulated 1 32 Accumulated 2 33 Flow rate 1 34 Flow rate 2 35 Connected with hardware output SW output bit (Not connected as OUT2 does not have the hardware) Temperature 1 36 Temperature 2 37 Pressure 1 38 Pressure 2 39 Pulse output 2 65 This is valid only when the output object of OUT2 is pulse output.
Note 17) Frequency with problem is displayed by flashing error code. Refer to [4-5-1. Alarms for IZT43]. Note 18) Frequency of the high voltage power supply module with a problem is displayed by flashing error code. Refer to [4-5-1. Alarms for IZT43]. High voltage power supply module without problem indicates normal status.
(Outside of 24 V+/-10%) The power supply voltage between the power supply terminal PWR_24V and PWR_GND is below 17 V. 2 Power supply error Use a power supply voltage of 24 VDC+/-10%. (Below 17 V) Change the setting of the DIP switch correctly. (Refer to operation manual K35-OMW0030).
For M8 connector when not used. 15 Connector (PORT1) Connector for Residual Pressure Relief Valve. 16 Connector (PORT2) Connector for Standby E/P regulator or Standby regulator. 17 Connector (PORT3) Connector for Standby/Isolation signal. 18 Connector (PORT4) Connector for external I/O device or IO-Link device. : For EtherCAT -17No.PF-OMA1007-B Display Part Description Main display Displays
Maintenance P.17 1) Inspection P.17 2) Overhaul P.18 3) Disassembly P.18 4) Assembly P.19 5) Expendable supplies P.20 6) Replacement procedure of seal P.21 7) Inspection P.22 5. Troubleshooting P.23 6. Construction P.26 7.
No. , 15 No.120 No.2131 No. 1 2 3 4 5 1 1 2 3 4 5 2 6 7 8 9 10 3 11 12 13 14 15 4 16 17 18 19 20 20 - ,No.131(OUT 15), No. (:ON:OFF) No. 1 2 3 4 5 No. No.
(At this stage, O-rings 23 and 24 are attached to the groove.) (8) Mount the O-ring 25 to the solenoid valve 17 and fix with hexagon socket head cap screws to the sub-plate 19 . 23 18 24 17 25 19 20 24 23 (9) After assembly is completed, perform an operation test and check that there is no air leakage. -36- Troubleshooting Refer Problem Possible cause Solution ence page 16 Supply pressure
No.MRQB-OM02 / / / / / / / / MRQ MRQ MRQ MRQ 1 1. 1. 1. 1. 11 1-1. 11 1-2. 11 1-3. 11 2. 2. 2. 2. 12 3. 3. 3. 3. 14 3-1. 14 3-2. 14 4. 4. 4. 4. 15 4-1. 15 4-2. 16 4-3. 17 4-4. 17 4-5. 18 4-6. 18 5. 5. 5. 5. 19 5-1. 19 5-2. 21 5-3. 22 6. 6. 6. 6. 24 6-1. 24 6-2. 24 6-3. 25 7. 7. 7. 7. 26 8. 8. 8. 8. 27 9. 9. 9. 9. 28 (ISO/IEC)(JIS) *1) *2) *1) ISO 4414: Pneumatic fluid power
Load file check Old:LES11-1-17 The setting content of Basic / Unit name in the file that is loaded (the file that was saved in the teaching box). New:LES11-1-28 Type:Step+2Pr The setting content of Basic / Para protect in the file that is loaded (the file that was saved in the teaching box). Refer to the table below.
LEC-OM08003 // LEC-T1 Series LEC6 LECPA TB Ver2.1 .5 .7 1. .9 1.1 .9 1.9 2.10 1.2 .11 1.11 2. .12 3. .13 3.1 .13 (1).13 (2)Tree .13 3. .14 (1).14 (2)Tree .15 4.16 5. .17 5.1 .18 5.2 .19 (1).19 (2).19 5.3 .20 (1).21 (1-1) LECPLECA 22 (2) .23 (2-1) LECPLECA 23 (2-1-a) TB Ver1.**. 23 (2-1-b) TB Ver2.**. 25 (2-2) LECPLECA 27 (2-2-a) TB Ver1.**. 27 (2-2-b) TB Ver2.**. 29 (2-3) LECPLECA .32 1
Initial Setting.16 4. 1 Gateway unit Communication speed switch (STATION NO.,B RATE) 16 4. 2 Setting the switch to change the communication CN2SW.17 4. Setting of controller (LEC) .18 5. External connection .21 5. 1 CN4: Power supply connector .21 5. 2 CN3: Bus connector .21 5. 3 CN1: CONT connector.21 5. 4 CN2: PC/TB connector.22 6.
Setting the switch to change the communication (CN2SW).17 4. 3. Setting of controller (LEC).18 5. External connection .21 5. 1 CN4: Power supply connector .21 5. 2 CN3: Bus connector .21 5. 3 CN1: CONT connector.21 5. 4 CN2: PC/TB connector.22 6.
Enter "password". 17 - (2) Set the controller so that the communication speed can be changed. Change "Parameter protect" setting so that "Communication speed" parameter can be changed. View the parameters of the controller. (2)-1 Change parameter protect to [3: Common + Extend + Step]. (2)-2 Select Download.
Rear panel Terminal block 1 2 3 PE Customer connection side Terminal connecting screw: M3 Crimping terminal width: 6.5mm and below Applicable electrical wire:1.25mm2 or more Rubber grommet Rubber grommet Power cable inlet Signal cable inlet Wire gage: up to 17 Wire gage: up to 17 12-3 Remote operation IDFA Series 12 2 IDX-OM-W016 Air dryer 12 Specification for Option T 12-5 Electric circuit
No.EX-OMU0028-D PRODUCT NAME SMC Wireless System EtherNet/IP compatible MODEL / Series / Product Number EX600-WEN# (Base) EX600-WSV# (Remote) Contents Safety Instructions 2 SMC Wireless System Features 10 SMC Wireless System Outline 11 Outline 11 System configuration 12 Base 13 Remote 14 Definition and terminology 15 Assembly 17 Mounting and Installation 20 Installation 20 Model Indication
No.EX-OMW0006-D PRODUCT NAME SMC Wireless System PROFINET compatible MODEL / Series / Product Number EX600-WPN# (Base) EX600-WSV# (Remote) Contents Safety Instructions 2 SMC Wireless System Features 10 SMC Wireless System Outline 11 Outline 11 System configuration 12 Base 13 Remote 14 Definition and terminology 15 Assembly 17 Mounting and Installation 20 Installation 20 Model Indication and
OFF [16] Turn on Servo to turn on ALARM. [17] After confirming that ALARM is turned on, turn ON ALARM OFF on IN0 and IN3 to start move to the position No. 9. (The rest is omitted.) Speed 0 51 No.
Compressed air pressure gauge Cooling water inlet 225 85 165 Drain with plug Rc 3/8 IDU6D, 8D IDF6D, 8D IDU11C to 75C IDF11C to 75C Power cord outlet (17) Grommet with waist Transformer integrated Front side Signal cord outlet (17) Signal cord outlet (17) Grommet with waist The power supply transformer can be integrated with an air dryer.
Exhaust port type 1 Common exhaust Valve stations VK 02 2 stations VZ Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 17 17 stations VT Manifold Specifications VP Common exhaust Manifold type B mount 17 stations Note) VG Max. number of stations Applicable solenoid
DC (+) 1 NC 2 DC () 3 OUT 4 Flow direction 17 Series PFA/PFW Digital Flow Switch for Air/Water Operating Unit Nomenclature LED Display RESET Buttons Displays the instantaneous flow rate, cumulative flow rate, and setting value. The mark blinks when the cumulative flow rate is being measured. Pressing the UP and DOWN buttons simultaneously activates the RESET function.