Ejector Valve Unit Series ZYY/ZYX 1 ZX B B' A B ZR A B P1 A A' ZM !0 o r t ZH ZU Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com e ZL ZY ZQ ZF ZP !1 ZCU Section A-A' (Ejector) AMJ !
to class B Rated coil voltage Allowable voltage fluctuation Note 2) VG Coil insulation type VP Note 1) With a light/surge voltage suppressor and power saving circuit, the light consumes a power equivalent to 2 mA.
side SS070A-B (for separable base) 7.2 Valve Valve 1 (P) 3 (R) This assembly is used to secure the manifold when a large number of stations are manifolded.
s t r u c t u r e a n d o p e r a t i o n p r i n c i p l e C u s h i o n s M a i n t e n a n c e I n s p e c t i o n P e r i o d i c i n s p e c t i o n D i sassem ble and reassem bl e C a u t i o n o f d i s a s s e m b l e D i s a s s e m b l i n g p r o c e d u r e A s s e m b l e p r o c e d u r e T r o u bl e s hoo t i n g Safety Instructions These safety instructions
Bumper B Magnet Slide Bearing Felt Holder Ball bushing Piston seal Rod seal Gasket A Gasket B No.
Latching style Latching style AC () () (+) 100V AC, 200V AC 100V AC, 200V AC Reset B C Set Yellow Yellow Blue Red A A Single solenoid (AC) Latching solenoid (AC) COM. Blue Red Blue Red SOL. C C A set A SOL. Reset Gray Gray Single style B C COM SOL. SOL.
JIS B 8361: General rules for hydraulic equipment. JIS B 9960-1: Safety of machinery Electrical equipment for machines. (Part 1: General requirements) JIS B 8433-1993: Manipulating industrial robots Safety. etc. *2) Labor Safety and Sanitation Law, etc. Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
At this time, magnet B goes out of the movement range of auto switch B, causing auto switch B to turn OFF. Furthermore, the piston moves to the right, causing magnet A to enter the movement range of auto switch A. As a result, auto switch A turns ON. 38 - Maintenance and Inspection Periodic inspection is necessary for optimum use.
Description Body cover Bearing cap Damper End cover A End cover B Photomicrosensor Sensor plate Connector A Connector B No.
PF3W711/721 (Vinyl chloride piping) -81No.PF-OMM0005-N Flow characteristics of the flow rate adjustment valve PF3W704S PF3W720S PF3W740S -82No.PF-OMM0005-N Analogue output Analogue output (Flow) (PF3W704/720/740) A B C Voltage output 1 V 1.5 V 5 V Current output 4 mA 6 mA 20 mA (PF3W711) A B C Voltage output 1 V 1.4 V 5 V Current output 4 mA 5.6 mA 20 mA (PF3W721-12/14) A B C Voltage output
A A 100mm 100 100mm 100 5mm 5mm 6mm 6mm 8mm 8mm 10mm 10mm B B Without cable Without cable 8m * 8m * Nil Nil 8 8 1.5m 1 1.5m 1 10m * 10m * A A 1000 1000mm 1000mm 1000 3m 3 3m 3 15m * 15m * B B *Refer to the table of Applicable stroke 5m 5m 20m * 20m * 5 5 C C *Applicable stroke Standard produced upon receipt of order *produced upon receipt of order (Only Robotic type cablecan be selected
B Width across flats B1 REC CX CY Mounting hole Width across flats B2 Width across flats NA MQQ M S + Stroke LS + Stroke ZZ + Stroke RHC MK(2) Single acting, Spring extend: CVM3L T Bore size Stroke RS Q G RS H A H + Stroke RZQ MI W S CEP1 Z + Stroke ZZ + 2 x stroke CE1 CE2 ML2B Bore size (mm) B2 MM LZ LY LX LT LH LD H1 B1 LC H B K F AL NA H2 I D A N 20 25 32 40 26 M8 x 1.25 55 70.5 40 3.2
Fig.7 3: Pay attention not to apply a strong impact to a feed back shaft of the positioner when the shaft is B connected to a fork lever-type fitting. The angle sensor might be damaged due to the strong impact. Do not apply any impact when the positioner and actuator are connected.
When performing the piping work, turn the tightening tool in the horizontal direction to the hexagon across flats of the body B so that any moment is not applied to the body A. If the tool is in contact with the body A, this may cause the body B to come off.
Switching hub Device that works as a relay in the network. -15No.EX-OMV1026-B Revision history A: Contents are added. [August 2018] B: Contents are added.
RS Q G ND hole H10 RS H A Rod dg RZQ +0.2 0 NX MI W S CEP1 Material: Rolled steel Material: Brass Material: Iron CE1 Applicable bore size A1 L1 L MM Part no. Y-J010B Applicable bore size Applicable bore size B C d H B C d H Part no.
AR50-D/ AR60-D Bracket 1) Mounting of bracket A Insert bracket A from the front of the regulator so that the fingers of the bracket A hold the regulator at the groove and the bottom of the body. Regulator Groove Bottom of the body Bracket A Fingers 2) Mounting of bracket B Fix the bracket B with the set screw (2 pcs.) included in the package.
The example of link connection which consists of telecommunication cable LEC-CG 1-1 and cable LEC-CG 2-1 between branches is shown below. 3 LEC-CG2b) M12 4pin b) M12 4pin male connector male connector 2 LEC-CGD 2 LEC-CGD 4 5 c) M12 4pin female connector 1 LEC-CG1b) M12 4pin b) M12 4pin male connector male connector a) RJ45 male connector with a shield8P 1 LEC-CG11 LEC-CG1a) RJ45 male connector
Features 2 Model Selection 1 Obtain the correction factor for the temperature from data A or B and the correction factor for the air pressure from data C. Temperature Data A or B = Series IDU: Data A IDF1D to 240D: Data B-1 IDF 370B: Data B-2 Air pressure Data C = Series IDU and Series IDF: Data C 2 Calculate corrected air flow by using A or B and C.