Pilot Operated Regulator AR425 to 935 Series Note 2) Use caution not to tighten excessively when mounting a pressure gauge, otherwise it may result in a breakdown. Use a sealant tape for sealing.
Note 2) Use caution not to tighten excessively when mounting a pressure gauge, otherwise it may result in a breakdown. Use a pipe tape for sealing. Recommended torque: 12 to 14 Nm.
The tensile strength of the power cord is 49N, and pulling it with a greater force can cause failure. Warning 1. Vacuum pressure switches There will be no change in performance if a pressure of approximately 0.5MPa is applied momentarily (when releasing vacuum), but care should be taken that pressures of 0.2MPa or more are not applied on a regular basis. Operating Environment 3.
For drain piping, use a pipe whose I.D. is not less than 5 and length not more than 5 m.Avoid riser piping. Maintenance Caution Caution Provide a stop valve before the ADM200 to facilitate maintenance and inspection. If the valve becomes clogged with debris, press the manual button to flush out the debris. Otherwise, it could lead to malfunction.
Model Size C10 A 10 ZP10C B 12 C 4 D 13 E F Y 1.7 12 12 12.5 14 14 14.5 18.5 19.5 3.8 7.7 7.7 8.2 9.5 9.5 10 13.7 14.7 ZP10U to 50U C13 13 ZP13C 15 4 13 1.8 C16 16 ZP16C 18 4 13 1.2 C20 20 ZP20C 23 4 15 1.7 C25 25 ZP25C 28 4 15 1.8 C32 32 ZP32C 35 4 15 2.3 C40 40 ZP40C 43 7 18 3.3 C50 50 ZP50C 53 7 18 Deep (D) ZP10D to 40D Model Size U02 A ZP02U B 2.6 C 1.2 D E F Y 2 4 6 8 10 13 16 20 25
The element can be replaced with a single touch. AMJ 30 0003 2R ZR ZM Body size Pressure gauge position 30 3/8 None Bracket Nil ZH 40 1/2 B Option 50 3/4 ZU Drain cock Nil Metal bowl 2 ZL Thread type Port size Nylon bowl 6 Drain guide (Rc 1/4) 02 1/4 Nil Rc J ZY 03 3/8 Flow: Right Left F G R 04 1/2 N If ordering two options or more, indicate symbols numerically and alphabetically.
For details, refer to the back of page 6, Procedure for replacing or changing the mounting angle of a pressure gauge. Mounting angle view (-R specification) MPa OUT IN K P C U O S L H to 2
Use a tool such as long-nose pliers if it is difficult to pull out by hand. 1. Withdraw the tubing straight. 2. When reusing the tubing, cut off the previously installed portion of the tubing to avoid possible leakage and/or disconnection of the tubing. 3.2, 4 Port size 3 5 32 04 M3 x 0.5 M5 x 0.8 3.2 4 15-6-28
Clean Regulator SRH Series ARJ AR425 to 935 How to Order ARX 02 SRH 3 0 0 0 AMR Gauge port orientation ARM Body size 3 4 1/4 3/8 Nil: Standard ARP OUT IN Washing grade IR-A 0 1 Grade A Grade B Knob Gauge port IR R: R Specification Set pressure Gauge port IRV 0 1 0.02 to 0.2 MPa 0.05 to 0.7 MPa OUT IN VEX Relief mechanism There is only one gauge port. 0 1 Non-relief Relief SRH SRH Made to
VEA 5 (R1) 4 (A) 1 (P) 2 (B) VY2 OFF state VBA VBAT F1 < F2 condition: See figure q. 2 (B) 3 (R2) AP100 4 (A) ON state Immediately after turning on F1 > F2: See figure e. Thereafter F1 = F2: See figure w. 4 (A) 1 (P) 2 (B) 3 (R2) Inw, port 3(R) is half open. 705
Nil V Standard For vacuum X505 VPA500 series Port size Symbol Port size VPA300 1/8 1/4 3/8 1/2 VPA500 VPA700 01 02 03 04 Bracket Nil F Without bracket With bracket Thread type Type of actuation A B N.C. (Normally closed) N.O. (Normally open) Nil F N T Rc G NPT NPTF VPA700 series Specifications Air Fluid N.C. or N.O.
+60C) Linear Low density polyethylene Operating Temperature Material Hardness Shore A 98A, Shore D 55D Note: Working pressure decreases as temperature increases.
Solenoid Direction: Opposite side of A port (A port bottom ported for Type 40), Type: 42 (A Port Side Ported; 42S: Solenoids on the Same Side of A Port), Stations: 04, Port Size: 01 (Rc 1/8)
Solenoid Direction: Opposite side of A port (A port bottom ported for Type 40), Type: 42 (A Port Side Ported; 42S: Solenoids on the Same Side of A Port), Stations: 04, Port Size: 01 (Rc 1/8), Thread: N (NPT)
Solenoid Direction: Opposite side of A port (A port bottom ported for Type 40), Type: 42 (A Port Side Ported; 42S: Solenoids on the Same Side of A Port), Stations: 04, Port Size: C6 (ø6 Cassette), Thread: N (NPT)
Solenoid Direction: Opposite side of A port (A port bottom ported for Type 40), Type: 42 (A Port Side Ported; 42S: Solenoids on the Same Side of A Port), Stations: 04, Port Size: 01 (Rc 1/8), Thread: T (NPTF)
Solenoid Direction: Opposite side of A port (A port bottom ported for Type 40), Type: 42 (A Port Side Ported; 42S: Solenoids on the Same Side of A Port), Stations: 04, Port Size: 01 (Rc 1/8), Thread: F (G)
When mounting models D-M9(V), M9W(V), M9A(V), and A9(V) with between 32 and 50 on sides other than the port side, please order a switch mounting bracket separately as per the instructions on page 17, and refer to cases CDQP2B32 to 100 in Information (04-E514) Cylinder with Compact Auto Switch.
Note 2) in part numbers for a round pressure gauge indicates a type of connection threads. No indication is necessary for R; however, indicate and N for NPT. Contact SMC for regarding the connection thread NPT and pressure gauge supply for PSI unit specifications. Note 3) Includes one O-ring and 2 mounting screws. Note 4) Assembly includes a bracket and 2 mounting screws.
J 1n 114 250 3/8 350 112 450 3/4 5 5 0 1 650 1 1i2 850-2 I I Port Sr" I PT pofts ilodel Bracket Beplacement Element AMG150 BM5'I AMG-EL150 02 1/4 (AMG 1s0) 03 3y8 (AMG 250) 04 1/2 (AMG 350) 06 3/4 (AMG 4s0) 1 o 1 ( A M G 5 5 O ) 14 1 1/2 (AMG 6s0) 20-2(AMGsso) AMG250 BM52 AMG-EL25O AMG35O BM53 AMG-EL35O AMG45O BM54 AMG-EL45O AMG550 BM55 AMG-EL55O AMG65O BM56 AMG-EL65O AMG850 BM57 AMG-EL85O