Sine Rodless Cylinder Series REBR Direct Mount Type (Do not adjust more than 2mm, as it will not be possible to obtain smooth acceleration and deceleration.) Do not adjust based on the stopper's movement, as this can cause cylinder damage. Stroke Adjustment Loosen the round head Phillips screws, and remove the top covers and dust covers (4pcs.).
Note 2) The output functions operate only for the real-time flow rate display, and do not operate for the accumulated flow display. Note 3) Window comparator mode Since hysteresis is 3 digits, separate P1 and P2 by 7 digits or more. 1 digit is the minimum setting unit (refer to the table above).
Note 2) The output functions operate only for the real-time flow rate display, and do not operate for the accumulated flow display.
Single action positive operation X View M A Automatic / Manual change-over screw (Built-in bleed restriction) Sensitivity adjusting screw (Adjusts GAIN) Stopper screw (Do not move) (15) Diaphragm valve SUP OUT2 OUT1 X (1) Pilot valve Supply valve A Supply valve B (8) Feedback lever (9) Span adjusting lever (7) Exhaust valve Span adjusting lever shaft EXH. (4) Counter weight Diaphragm For
Before piping and screwing in couplings, please make sure that sludge trom pipe threading and sealing materials do not go into the pipe. When seal tape is used, tape winding should be done so that 2 threads are left untaDed on the end.
Please make sure that operating conditions do not cause problems since the use of FEP tubing under chemical environment is unsecured.
Orifice size Electrical entry Orifice diameter 2mm 3mm 4mm 5mm 7mm Class 4 Class 3 Class 2 Symbol 2 3 4 5 7 Voltage G C T TL D DL DO Grommet Conduit Conduit terminal Conduit terminal with light DIN connector DIN connector with light 1 2 3 4 5 6 100VAC 200VAC 110VAC 220VAC 24VDC 12VDC For DIN connector (without connector) All are equipped with surge voltage suppressor.
D -DIN connector DL -DIN connector with light DO-For DIN connector (without connector) Orifice and port size combinations T -With conduit terminal TL-With conduit terminal/light Class Orifice diameter Port size 2 3 4 5 7 10 1/8 (6A) 2 1/4 (8A) 1/4 (8A) 3 3/8 (10A) 1/2 (15A) Connector 1/4 (8A) 3/8 (10A) 4 All class B coils are equipped with surge voltage suppressor.
Do not use any cable other than this cable. 16
Wiring Power supply and N/A communication connector Power LED Communication LED Fig.1 Display and Communication * Please don't do the insert and remove of live-wire after the power supply is turned on. It causes the communication abnormality with the master by the situation.
(Default value : 100%2.00MPa) (Note3) Do not input the signal as like output the pressure of more than 100%. Please use in a range of rating. (Note4) The difference between F_1 and F_2 is adjustable in a range of 10% of the rated value. (Note5) The adjustment like making the relation of F_1 > F_2 is not available.
BRAZIL SMC Pneumaticos do Brazil Ltda. CHILE SMC Pneumatics (Chile) S.A. PERU SMC Corporation Peru S.A.C. VENEZUELA SMC Neumatica Venezuela S.A. OCEANIA AUSTRALIA SMC Pneumatics (Australia) Pty. Ltd. NEW ZEALAND SMC Pneumatics (N.Z.) Ltd. EUROPE AUSTRIA SMC Pneumatik GmbH (Austria) BELGIUM SMC Pneumatics N.V./S.A.
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 37
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 38
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not reuse if disassembled. High strength adhesive is applied to the portion of the connection that is threaded to prevent it from loosening, and it must not be disassembled. If it is forcefully disassembled, it could lead to damage. J J 2.The dust cover may stick to the stud.
Do not use an application to operate several cylinders simultaneously by adjusting cylinder speed. If this is inevitable, use a high rigid guide against load, so that the cylinder is not damaged even when the each cylinder output is slightly different. 4.
Do not cut the tube with cutting pliers, nippers, scissors, etc.) 2. Grasp the tube, then slowly push it until it comes to a stop. 3. Then, pull it back gently to make sure that it does not come out.
Note 5) Do not use the V-band type for gases. FGES/FGEL type (V-band type) FGET type (Bolt tightening type) Suitable for medium flow rate, low pressure filtration. Element replacement is easy with the V-band type.