MNB B Z + Stroke DB DX DD 90 B 4DT A DS DH 4DR DB DU DO DO DC DE DU DL Rotation (mm) No.
(mm) 02 04 06 08 10 13 16 20 25 32 40 50 2 4 6 8 10 13 16 20 25 32 40 50 Pad type 02 04 06 08 10 13 16 20 25 32 40 50 2 4 6 8 10 13 16 20 25 32 40 50 Pressure gauge position Thread dia.
Do not turn the piston rod with the rod boot kept locked. When turning the piston rod, loosen the band once and do not twist the rod boot.
Do not wire with power lines or high voltage lines. Wire separately from power lines or high voltage lines, avoiding parallel wiring or wiring in the same conduit with these lines. Control circuits, including switches, may malfunction due to noise from these other lines. 5. Do not allow short circuiting of loads.
DC DE DO 4 x DR DU DL DA DU With Rubber Bumper [mm] [mm] Bore size Z Part no.
Do not repair or patch the replaced tubing or fittings for reuse. 1. Do not use in environments or locations where there is a danger of damage to fittings and tubing. For fitting and tubing materials, refer to specifications and construction drawings, etc. 2. Provide shade in locations which receive direct sunlight. Caution 1.
%sillrc I SERIES NCJ2 Standard Type: Single Acting/ Spring Extend Spring Extend/Rod Side Flange Type (F) rucrzr lEi," F4-l sr'or,Jl r NCJ2F6 Rod Cover Head Cover NCJ2Fl0, 16 .sE (114") a10 o16 (5i8") BORE SIZE .06 l'v4"t s10 (3/8") o16 (5/8") * In case of auto switch with 06 bore, add smm to S and Z. Spring Extend/Double ClevisType (D) r.rcJzo [e*" "i'"F] qE6] r ocDaSocr?
I %sillrc SERIES NCJ2 Standard Type: Single Acting/ Spring Extend Spring Extend/Rod Side Flange Type (F) rucrzr lEi," F4-l sr'or,Jl r NCJ2F6 Rod Cover Head Cover NCJ2Fl0, 16 .sE (114") a10 o16 (5i8") BORE SIZE .06 l'v4"t s10 (3/8") o16 (5/8") * In case of auto switch with 06 bore, add smm to S and Z. Spring Extend/Double ClevisType (D) r.rcJzo [e*" "i'"F] qE6] r ocDaSocr?
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not unpack the device until installing it. Do not drop or knock the controller. Keep the flow ports and cable glands plugged until installing.
Slandard sub-plates do nol provide for pilot presaure connections through the sub-Plale, ,^""." ,"-,."*, I tf-ffiA--n | \ r l l B = BOTTOM 9B-SIOE&BOTTOM NVS 4034 SUBPLATES Gonofal: Sub-plates are heavy duty aluminum die castlngs.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not use in a location where radiated heat will be received from a heat source in the vicinity. 5.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not use in a location where radiated heat will be received from a heat source in the vicinity. 5.
AXT632-69-1 AXT632-69-2 VVCA40-3A-06-2 VVCA40-3A-06-1 OR-3200-200-H VCA45--VVCA40-6-n VVCA40-4A-06-2 VVCA40-4A-06-1 Material Mounting screw (side port) Mounting screw (side port) q q Steel Steel Mounting screw (front port) Mounting screw (front port) End plate assembly (D side, side port) End plate assembly (D side, side port) w w Aluminum Aluminum End plate assembly (D side, front port)
Do not use fluid containing solid matter. This will cause faulty operation. IR IRV VEX SRH SRP SRF SRF ITV IC ITVH ITVX PVQ VY1 VBA VBAT AP100 891
Although switches satisfy the IEC standard IP67 structure (JIS C0920: anti-immersion structure) (except D-A3l, A44l, G39l, K39l), do not use switches in applications where they are continually exposed to water splash or spray.
Operating Environment Maintenance Caution Warning 1.Do not use in atmospheres where the valve is in direct contact with corrosive gases, chemicals, salt water, water or steam. 2.Do not use in locations subject to vibration or impact.
Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 2. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire. Consult SMC regarding use in this kind of environment. 3.
This do-it-yourself building block manifold is widely used in the emission analyzer and gas processing fields. The new style modules are 90% machined and drilled from bar stock. Each module can be in a center or end position in the manifold.